e heavier and larger in size than steam turbine

Q: turbine. All the components are mounted on the same shaft. The pressure and temperature of air at…

A: Initial pressure, Pi=1.5 bars Initial pressure, Pf=6 bars Initial temperature, Ti=293 K Efficiencies…

Q: to 0.45 MPa. For 180 kg/s of steam, determine the work, the thermal efficiency, and the steam rate…

A:

Q: (a) Using appropriate diagrams, show the differences between an open cycle and a closed cycle gas…

A: OPEN CYCLE  1. Atmospheric air is sucked in compressor and it is combusted in combustion chamber by…

Q: Otto Cycle is commonly used as an ideal cycle for spark-ignition engines. Given an Ideal Otto Cycle…

A:

Q: Steam at 6.2 MPa and 480 deg. C is received by a regenerative engine with ideal conditions and in an…

A:

Q: a. State diagrams of the cycles, and b. Sample calculations of the performance of the cycles in…

A:

Q: 136 kg/s steam with an inlet condition of 52 bar, 400 C enters a rankine turbine and expands to 36…

A: The solution is attached below:

Q: 2. What are the four processes of Rankine Cycle

A: Carnot cycle is the ideal cycle for heat engine. Rankine cycle is similar role as Carnot cycle used…

Q: A Rankine cycle has the following operating conditions: Steam Pressure, 2.6 MPa Steam temperature,…

A:

Q: team turbine plants.. 3. 'Gas turbines req

A: given: Consider the following statements: 1. The speed of rotation of the moving elements of gas…

Q: In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then…

A:

Q: Figure 5.15 in the text gives a schematic of a Carnot cycle operating with a H₂O liquid/vapor with a…

A:

Q: What is an approximate cost of starting and running a Gas Turbine Power Plant running on Diesel…

A: Solution I have given rough estimate to make gas turbine power plant from a project to be made.hope…

Q: 6. At two stages when equal pressure ratio are maintained the work output C. optimum. d. none of the…

A:

Q: A 330 MW steam power plant operates according to the simple ideal Rankine cycle. The water vapor…

A:

Q: In a Rankine Cycle, real work required by the pump is less that the isentropic work. True False

A:

Q: a) Water vapor expands through the turbine, developing power. b) Water condenses in the large…

A: here all option a ,b,c,d,e, are all correct

Q: 1. Where do you think the 70% (gasoline) and the other 50% (diesel) of the energies of the two…

A: See the all these engines are irreversible heat engines. That is they have loss of some kind in…

Q: Helium gas is used as the intermediate fluid in an ideal Brayton cycle with a regenerator. Helium…

A:

Q: Muhammad is a Mechanical Engineering major at UCR, and his team just got their butts kicked by an ME…

A: Solution:-As per questions description.The P.V diagram d-muhammad's power cycle is -shown below.At…

Q: 3.1 Describe with the aid of a plant layout and p-v and T-s diagrams, the working of simple closed…

A: To describe: The working principle of simple close circuit, ideal and actual constant pressure gas…

Q: Consider the Diesel engine cycle below: 3 V 1-2 Adiabatic. 2-3 Constant-pressure. 3-4 Adiabatic. 4-1…

A:

Q: If a Diesel cycle and Otto cycle have the same initial conditions, the same compression ratio, and…

A: When the piston is at the bottom of its stroke ('bottom dead centre', tdc), the compression…

Q: rk, the thermal efficiency, and the steam rate (a) fot the cycle e same specifications, the brake…

A: P1=5.2MPaT1=400CP2=0.036MPam=136kg/sSteam rate =4.80kg/kwhefficiency =93% To-Find:- Brake thermal…

Q: How much does it cost to start and run a Gas Turbine Power Plant running on Diesel Fuel?

A: Gas turbine  During times of high electricity demand, gas turbines have been utilized to generate…

Q: 1. Compare and evaluate the actual and ideal thermal efficiencies and back work ratio 2. Construct…

A:

Q: State h(kJ/kg) s(kJ/kg-K) 1 3642 7 4 200 0.7 f the temperature of state 2 is 40°C then the maximum…

A:

Q: Draw and label the P-V and T-S diagrams. You are to design a 500 MW gas turbine power plant running…

A: In an ideal Brayton cycle, the rate of heat transfer takes place at constant pressure process, and…

Q: For a Rankine cycle, decreasing minimum pressure while holding all other parameters constant will…

A: The Rankine cycle contains the following processes: 1-2: Reversible adiabatic pumping 2-3: Constant…

Q: A turbine receives steam at 100 bar, 600°C and exhausts it at 2 bar from which it is used for…

A:

Q: A Brayton cycle is used to produce power. Air flowing at 40 lbm/s enters the compressor at one…

A:

Q: a) Illustrate (by a sketch showing main components) and describe how a multistage (show 2 stage) gas…

A: Objective: To illustrate and describe 2 stage gas turbine cycle including regeneration. clearly…

Q: turbine plants.. 3. 'Gas turbines require cooling water for its operations.

A: given: Consider the following statements: 1. The speed of rotation of the moving elements of gas…

Q: Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 300 K, with a…

A: Inlet condition at compressor : T1=300 K P1=100kPa V1˙=5m3/s T3 = 1400 K r1 = 6 r2 =8 r3 = 12

Q: Enumerate the advantages of piston engines over gas turbines. 1. 2. 3.

A: Piston engines are more efficient and offer a lower specific fuel consumption (. 43 lbs./hp/hr)…

Q: For an air standard Diesel Cycle, determine the following: 1) Clearance volume (ft3) 2) Maximum…

A:

Q: (i) List the name of the four processes in a generic Carnot cycle and state what type of energy…

A: Carnot cycle : A Carnot cycle is a theoretical perfect thermodynamic cycle suggested by Sadi Carnot,…

Q: Explain and contrast the functionality of a steam turbine and gas turbine engine. Sketch the main…

A: Introduction:- Boilers are pressure vessel which is sued mainly on ships where the water is heated…

Q: The efficiency of a gas turbine is much larger than that of a steam turbine since   Question 4…

A: given = multiple choice question

Q: What is the compression ratio?

A: The rejected energy is twice the generated energy.Q1 = 2Q2The efficiency is the ratio of difference…

Q: a open cycle and a closed cycle gas turbine engine.

A: Difference between An open and a closed cycle gas turbine engine

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.