Note: Express your answer in terms of the units.Observe 3 decimal places.The error threshold is ± 2.50% Relative to the right answer. 1.) The reaction @ point D2.) The tension @ Cable BE.3.) The x-component of the reaction @ A.4.) The y-component of the reaction @A5.) The reaction @ A. OF DADNINGAA spherical tank with a radius of 3.1 m that has a mass of 27412.334 kg was supported in the system shown. Assuming friction and the bar weight is negligible, determine the following:EBWHSENERALTOS CITYB: 28.653 °8: 32.694NIVERSITYOTRE DAM

Answered: Image /qna-images/answer/4d5a39b3-8ea7-4dd2-8516-7ecdbe7c6f94.jpg

Answered: E B GA W DAD) ME OF C H ENERAL TOS CITY…

Engineering

Mechanical Engineering

E B GA W DAD) ME OF C H ENERAL TOS CITY A -NOTRE NIVERSITY

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.35P: The weight of the cylindrical tank is negligible in comparison to the weight of water it contains...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
The gate shown below has a homogeneous depth into the page of 5 meters. Label all parameters and perform a force analysis of the gate. Determine the minimum force P, that could hold the gate closed assuming a frictionless hinge. Open to atmosphere Water 3m Hinge B -2m- 4 m P
Q2 A sluice gate weighing (1.8tonnes) is raised and lowered using a square thread screw. The frictional resistance induced by water pressure against the gate when it lowers its position is 400Kg. The outside diameter of the screw is (6cm) and the pitch is (1cm). The outside and inside diameters of the washer are (15cm and 5cm) respectively. The coefficient of friction between the screw and nut is (0.1) and between the washer and seat is (0.12). Requirements: 1) Calculate the maximum force to be exerted at the end of the lever for raising and lowering the gate. 2) Efficiency of arrangement. 3) Number of thread and height of the nut, an allowable bearing pressure is 70Kg/cm². HA Thrust washer Nut Screw
4.3m shown in dragram below.The ocuter lecrel IS lom above the base Of the doun. If the dam iS 16-3m uidde, Cel culate the totel thrust on the deem. Tare density of weter >100okg/m3 a quadrant Fa cirle with radiusz A dam is formes from Fresh water lom R=73m SA E 30 Assumetim,SAE flinits
A 75 pound object needs to be lifted vertically one foot. You bave a 2-inch diamcter piston actuator with a 12-inch stroke connected to a 50 psi source of presSurized air. The mass is restricted by a set of guide rails, which imit it to vertical motion, and which ase roller bearings with & friction coefficient of 0.002. Can the object be lifted? How long I will it take?
keep the gate from opening when The circular gate ABC has a Im radius and is hinged at B. Compute the force P just sufficient to Question-2 (h 8 m). Neglect atmospheric pressure. %3D Pa 7- = 9790 km Water P. Im Im
4. A sliding gate of height 1.4m and width 2.8 lies in vertical plane that weighs 25KN. Determine the vertical force required to lit the gate when its upper edge is 6m below the free water surface and coefficient of friction between the gate and guides is 0.15. Determine the center of pressure acting on the gate. Water 6 m Gate- F-
An effort of 2 kN is required just to move a certain body up an inclined plane of angle 15°, the force acting nlel to the plane. If the angle of is agnation of the plane is fiade 20°, the effort required, againaplied parallel to the plane, is found to be 2.3 kN. Find the weight of the body and the coefficieraeo friction. (A) 3.9 kN, 0.258 (C) 3.8 kN, 0.24 (B) 4.5 kN, 0.26 (D) 3.8 kN, 0.268
A sliding gate of height 1.4m and width 2.8 lies in vertical plane that weighs 25kN. Determine the vertical force required to lift the gate when its upper edge is 6m below the free water surface and coefficient of friction between the gate and guides is 0.15. Determine the center of pressure acting on the gate.
Find the velouty I ear K-E = 11773 man SS kg.
Please Help