4.3m shown in dragram below.The ocuter lecrel IS lomabove the base Of the doun. If the dam iS 16-3m uidde,Cel culate the totel thrust on the deem. Tare density of weter>100okg/m3a quadrant Fa cirle with radiuszA dam is formes fromFresh waterlomR=73mSA E 30Assumetim,SAEflinits

Name: 4.3m shown in dragram below.The ocuter lecrel IS lomabove the base Of
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 4.3m shown in dragram below.The ocuter lecrel IS lomabove the base Of the doun. If the dam iS 16-3m uidde,Cel culate the totel thrust on the deem. Tare density of weter>100okg/m3a quadrant Fa cirle with radiuszA dam is formes fromFresh waterlomR=73m

Answered: Image /qna-images/answer/d9bd3637-2253-4a4c-9ceb-2937fb8489cc.jpg

Engineering

Mechanical Engineering

dam is formes from a quadrant f a ci +3m shownin dragram b elaw. Ihe wcuter lecrel is lom oaue the base Of the down. If the dam is 16-3m Ceul culate the totell thrust on the deem. T are densityof weter wide,

dam is formes from a quadrant f a ci +3m shownin dragram b elaw. Ihe wcuter lecrel is lom oaue the base Of the down. If the dam is 16-3m Ceul culate the totell thrust on the deem. T are densityof weter wide,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Qu: Caleulate the magnitude 4 direction of foree exerted on the three-quar ter cylinder (ABCD), shown in figure below, which is (3m) Long perpendiular to the figue. Also pove that this force passes through point ©. Water 2 m A B 0.6
19% @ uo 10:27 quiz1.docx Locate the centroid z of the right-elliptical cone. 10 ft 4 ff
Can you help me
Determine al Y for ce of Hhe mem bers trus shown 4 m 4 m 600 N
Find x1/F and x2/F.
magnitude of the reruttant water force Cper meter op width) acArngs on the face of the dam? A grauity dam has the cross section shown, lalhat is the 30m 20m 3om 20m
Problem no. 1. Compute the resultant and its location from pt. D 17 kN/m 4m 7m B 5m 3m 1m- D 8 kN/m
A motor car has a wheel base of 2.82 m has pivot centres 1.2 m. The track distancebetween tyre centre lines is 1.2m. If the angle of lock is 300and tyre width 100 mm,determine the minimum radius of the outer turning circle.
rerce D6 =blank Dimetr Yedaction Fn =0015 Y(Pi-CDp Ev-vam velocity PP- Panch Diametr FELt Ye Sreching force woling force drawing foreo 2. 25 ower Kx=0.98+o.02 Rd=die corner vadus mui die shape facArin extrustion -Lentn tthicknes YA=Stess ) Dirct on 1 The data given in Table Q1(a) corresponds to a cold heading operation performed to make square head on a steel bolt. Figure Q1(a) shows the dimensions of the bolt to be produced. Strength coefficient for the steel Table Q1(a) Strain hardening exponent 550 MPa Coefficient of friction at the die-work interface- 0.21 Thickness of wire stock out of which the bolt is made 0.16 Final length of the bolt. 10 mm 120 mm Compute: (i) The length of stock must project out of the die in order to provide sufficient volume of material for this upsetting operation. (ii) The total number of bolts that can be made out of 6 m rod (wire stock) (iii) The maximum force that the punch must apply to form the head 5 mm 10 mm 15 mm Figure Q1(a)
Q1. Find the horizontal thrust of the water on each foot of width of the sluice gate, given y₁ = 7 ft, y2 = 1.2 ft, and y3 = 1.4 ft. Neglect friction Water Y3 Gate 17
Find thedish eter D=75 E Luctun 32-Sm ETvetion 27m ifthe pressureis e qualin thetwo 28 Lit scales Sec 11
Compite the IMAf of the engine lift shown in The second diagram