e= 30° B 1000 lb

Q: Two blocks A and B each having a mass of 10 kg, are connected by the linkage shown. If the…

A:

Q: A tower guy wire is anchored by means of a bolt at A. The tension in the wire is 4000 N. Determine…

A: To determine the direction cosine angles for a given force in 3-D.   From the given figure,…

Q: Thebent rod is supported by a ball-and-socket joint at O, a cable at B, and a slider bearing at D.…

A: Calculating different vectors and their directions:

Q: The cable of the tower crane is subjected to 840 N force, the magnitude of the moment of the force F…

A: Solution: A0,0,0 , B3,2,24 , C15,10,0γAB→=3 i^+2 j^ +24 k^γBc→=12 i^+8 j^ -24 k^u^BC=γBc→γBc→=12812…

Q: A system of cables is shown and in a state of equilibrium. Using equilibrium equations, solve for…

A: To find tension in cable AB, BC, CD

Q: 3. A 600 lb load is supported by a cable which runs over a pulley and is fastened to the bar DE in…

A:

Q: b) The L bracket ABC is supported by a roller at A and a pin at B and is loaded with a system of…

A: Note:Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: 2-15. Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable…

A:

Q: The jacking mechanism consists of a link that has a square-threaded screw with a mean diameter of…

A: The free body diagram of the jack is shown below.

Q: Two blocks A and B, each having a mass of 5 kg, are connected by the linkage shown. If the…

A: The given data is shown below:

Q: 6 Ib www

A: draw the FBD  force in the spring = 3 lb deflection of spring ∆=PK ∆=38=0.375 inch=0.03125 ft

Q: Container W weighs 376 N. It is suspended from ring A. Cable BAC oases through the ring and is…

A: W=376 NTo find- Force vector for P and Q

Q: eering  If the tension in the gantry crane lifting cable is T = 14 kN.Define force T how as a…

A: Given:- T=14kN To find:- T

Q: 40 mm 75 mm B 75 mm 300 N 60° kA - y 350 mm 40°

A: Express the force as a vector. Also find the position vector of A with respect to O. Then using the…

Q: D 2 ft -2 ft- -2 ft A 90 65 200 lb 100 lb 2. A beam AB is loaded as shown. The beam is pin-connected…

A: Determine the pin reaction at A and the tension in the rope.

Q: The wall crane supports a load of 700lb. Determine the horizontal and vertical components of…

A: Support Reaction: When a number of forces operate on a body, and that body is backed by another…

Q: A- In Fig.A, Replace the loading system by an equivalent resultant force and specify where the…

A:

Q: . Determine the rotation angle of pulley D with

A:

Q: The two bars AC and CD are homogeneous and weigh 200 N/m. Joints A, C, and Dare ball-and- sockets,…

A:

Q: Knowing that the rod ABC and the cable BD are both made of steel, determine (a) the deflection at B,…

A: Given :- Rod ABC and cable BD are both made of steel  E = 200 GPa To determine :- (a) the deflection…

Q: Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square…

A: Given: Member AB is supported by a cable BC and at A by a square rod which fits loosely through the…

Q: 4.95 A 250 x 400-mm plate of mass 12 kg and a 300-mm-diameter pulley are welded to axle AC that is…

A:

Q: 4. Determine the x, y, z components of reaction at the ball-and-socket joint A and the tension in…

A:

Q: 1. A tower guy wire is anchored by means of a bolt at A. The tension in the wire is 4000 N.…

A:

Q: 4A.) The H m uniform rod as shown below weighs F÷2 N. Segment AB and BC is G m long. The cable acts…

A:

Q: a helical spring slope of helix ma be assumed small, is required to transmit a maximum pull of 1 kN…

A: To find the number of Coils (n) -

Q: Consider the frame as shown in the figure. A moment of 80 kN-m acts at the joint O, given that the…

A: Given data- Moment M=80 kN-m, Support B fails if the moment exceeds 18 kN-m, To Find- Whether…

Q: A C 10.6 m 2.1 m

A: tension will be same in the rope  make free body diagram (F.B.D.) then take moment about point A to…

Q: using the following method and then Draw the Shear and Moment Diagram. a.) Forçe Męthod

A:

Laws of Equilibrium

A body is said to be in equilibrium if the system of forces acting on the body tends to keep the body at rest, in other words, there is no translation motion or net torque on the body. Under such conditions, the equilibrium conditions are to be applied to analyze the condition. The branch of mechanics that deals with this condition is known as 'statics'. Under equilibrium, there are no net forces on the body.