dx V-x² + 4x – 3

Q: 4. Find the dimensions of a concrete lined open channel used to convey a discharge of 70 m/s. The…

A: Given data  Discharge  Mannings roughness coefficient  Side slope  Bed slope

Q: 20 IN H 1=3 m 3 d 1=3 m 1-3 m Which of the following most nearly gives the force in member cd due to…

A:

Q: GIVEN FIGURE SHOWN, DETERMINE THE FOLLOWING PROMPTS BELOW: у, m В 16, 0) -x, m |F =5 kN 60° *A (12,…

A:

Q: Question 1: For the truss below, using the method of joints: a) Calculate the degree of static…

A: Sorry I didn't see that you have asked for only part (b)  Ok but i have solved all the parts in…

Q: I) Determine the force in member DE of the truss. K J H G A A B 4 ft I O C o D E -3 ft 3 ft 3 ft 3…

A: Method of section is used to calculate Force in member DE  Taking moment about  G  To get Force in…

Q: FIHD THe CENTROID (x $ Y) of THe GazOMETRY

A: Centroid is the point where the mass of whole body acts. If there is a figure which consists of…

Q: '. (a) Compute the runoff from a 7-in rainfall on a 1500-acre watershed that has hydrologic soil…

A:

Q: 16. From a triangular steel plate XYZ, a triangular section VWZ was cleanly cut off. What should be…

A:

Q: The figure below shows a shaft of three segments. It is restrained (fixed support) at both sides and…

A: Finding out twist developed in steel from support B.

Q: t www h. The steel structure is loaded as shown. hc = 4 m, Lb = 3m, P = 40 KN, E = 200 GPa, Ib Ic=…

A:

Q: What is the Ix and Iy of the cross-section in mm4

A: Given: Required : Ix and Iy of the cross-section in mm4

Q: From the beam shown. Let P = 30 kN, Q = 2 kN/m, L =6m. PKN L/3 m QkN/m Lm Determine the following;…

A:

Q: 6. A biodegradable fuel having a specific gravity of 0.95 and a viscosity of 0.04 grams per cen-…

A: Solution (6) Reynolds number of the biodegradable fuel is calculated by. Re =ρvDμv =Re ×μρD Where, ρ…

Q: Derive the expression

A: Expression for change in length of the block

Q: +y") dx ly

A:

Q: 1. Y 3" r= 3" 4" 1" 2"

A:

Q: There is an access road 222m from PI3. Use the information from but assume a practical speed of…

A: Consider the given data and table Station SKD Level VC Length PI 1 1402 193.40   PI 2 1502…

Q: 4. A trapezoidal channel of bed width 8.0 m, side slopes are 1:1, longitudinal bed slope = 12 cm/Km,…

A:

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Q: Explain why wx = 2/3(9-x)

A: Given:Required:To explain loading intensity for 6<x<9

Q: 500 50 60 400 500 50 80 - 340 80

A:

Q: x+sinx 2. limx0 x+cosx

A:

Q: Solve for x 5-5x>7x+16

A: Given: 5-5x>7x+16

Q: Flange thickness of W36 x 800 is?

A: The given data is: W36 x 800 beam

Q: b. Draw the primary and redundant beam. Hint: use the roller at B as redundant. c. Determine the…

A: The reaction in an indeterminate beam can be calculated by assuming any support to be redundant.…

Q: Example 2: A soil Profile is shown in the figure A zone of capillary rise of 2.5m is on the sand…

A:

Q: Question 1: Draw Shear Force and Bending Moment Diagram R kN 10 kN/m 8 m 2 m RA Re R = Last two…

A:

Q: Calculate the area between offsets 1 and 10 in Figure 8.10 where these offsets, scaled. from the…

A:

Q: dy x3+y3 dx x²y+xy2

A:

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.