During the recrystallization of a cold-worked material, which of the following statement(s) is (are) true? There is some reduction in the number of dislocations. O Some of the internal strain energy is relieved. O The metal becomes more ductile, as in its precold-worked state. O Grains with high strains are replaced with new, unstrained grains. O There is a significant reduction in the number of dislocations, to approximately the number found in the precold-worked state. The thermal conductivity is recovered to its precold-worked state. O All of the internal strain energy is relieved. O The electrical conductivity is recovered to its precold-worked state.

During the recrystallization of a cold-worked material, which of the following statement(s) is (are) true? There is some reduction in the number of dislocations. O Some of the internal strain energy is relieved. O The metal becomes more ductile, as in its precold-worked state. O Grains with high strains are replaced with new, unstrained grains. O There is a significant reduction in the number of dislocations, to approximately the number found in the precold-worked state. The thermal conductivity is recovered to its precold-worked state. O All of the internal strain energy is relieved. O The electrical conductivity is recovered to its precold-worked state.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The yield strength for an alloy that has an average grain diameter of 5.9 x 10-2 mm is 148 MPa. At a grain diameter of 7.8 × 10-³ mm, the yield strength increases to 233 MPa. At what grain diameter, in mm, will the yield strength be 247 MPa? d = i mm
an alloy with an avg grain diameter of 0.053 mm is l16 MPa. When the grain diameter is 0.008Amm, the yeild strength goesupto 231 MPa.lf the yeild strength is 207MPA, what would the grain diameter be?
The yield strength for an alloy that has an average grain diameter of 5.2 x 102 mm is 110 MPa. At a grain diameter of 6.3 x 103 mm, the yield strength increases to 251 MPa. At what grain diameter, in mm, will the yield strength be 222 MPa? d = mm
Consider a single crystal of a hypothetical metal that has the BCC crystal structure. A stress of 50 MPa is applied in the [101] direction of the BCC unit cell.a. Determine the most favourable slip direction for the (011) slip plane of the BCC unit cell. ⟨111⟩ is the family of directions with the highest linear density in the BCC unit cell.b. If τcrss = 27.5 MPa, determine if the single crystal yields. If not, what stress level is required?c. What is the minimum stress at which the BCC single crystal yields?
need correct and explained properly
3. An uncold-worked brass specimen of average grain size 0.01 mm has a yield strength of 150 MPa (21,750 psi). Estimate the yield strength of this alloy after it has been heated to 500°C for 1000 s, if it is known that the value of σo is 25 MPa. (Note that the axis has logarithmic scale). Grain diameter (mm) (Logarithmic scale) 1.0 0.1 0.01 1 10 850°C 800°C 700°C 102 Time (min) (Logarithmic scale) 600°C 500°C 103 104
The yield strength for an alloy that has an average grain diameter of 4.6 x 10-2 mm is 105 MPa. At a grain diameter of 7.7 × 103 mm, the yield strength increases to 248 MPa. At what grain diameter, in mm, will the yield strength be 234 MPa? d = i mm
9. Consider a metal rod, whose grain size can be adjusted by different processing techniques. The graph below shows how the yield stress changes with grain size d; the x-axis is logarithmic. The curve reaches a limiting value of 60 MPa as indicated by the horizontal dashed line on the y-axis, for very large grain sizes. Also, you are given the information that at d = 25 microns (vertical dashed line), the yield stress is 100 MPa. Using this information, what will be the yield stress at d = 5 microns? Select the closest numerical value. Use the Hall-Petch relation in working out your answer. Yield stress (MPa) ● ● 228882S 130 120 110 100 60 10⁰ 10¹ 10² Grain size d (microns) 132.4 MPa 149.4 MPa 165.2 MPa 156.3 MPa 10
Problem 5. Starting with a 2-inch diameter rod of brass, we would like to process 0.2-inch diameter rods that possess minimum yield strength of 40 ksi and a minimum elongation to fracture of 40%, (see the following figure). Design a process that achieves that. 120 70% Cu-30% Zn 100 Tensile strength 80 60 60 Yield strength 40 40 20 20 Elongation 10 20 30 40 50 60 Percent cold work Tensile strength and yield strength (ksi) Elongation percent
Can you explain the kinetics of recovery, recrystallization, and grain growth? (Draw three plots showing the kinetics of each prosess and explain the plot)
Suppose that a wing component on an aircraft is fabri- cated from an aluminum alloy that has a plane-strain fracture toughness of 26.0 MPa Vm (23.7 ksi Vin.). It has been determined that fracture results at a stress of 112 MPa (16,240 psi) when the maximum internal crack length is 8.6 mm (0.34 in.). For this same component and alloy, compute the stress level at which fracture will occur for a critical internal crack length of 6.0 mm (0.24 in.).
summarize the way in which fine_grain microstructures behave with regard to low temperature and room temperature strength and toughnesd.why not make all metals as small_grained as possible?