| 1. A stacking fault region is a planar defect

Q: For steel, the energy to produce tensile failure is 105Jm 2 (i.e. fracture energy), modulus of…

A:

Q: Minimum thickness?

A: Given; A building has to be maintained at, TI=210 C (DB)Wet bulb, Tdb=10.170COutside temperature,…

Q: Name 2 types of bending?

A: Bending is a type of forming process in which the required object maybe a rod, tube or sheet metal…

Q: What is the operation of parting?

A: Parting operation

Q: During solidification of a pure molten metal,the Grains in the casting near the mould wall are3;…

A: Grain size or formation during the metal forming process in engineering represents the internal…

Q: pes o

A: GIVEN: Explain different types of fits?

Q: Elaborate the following terminology of drawing “SQ THD DIA 21X3 LH ?

A: The term pitch represents the distance between two successive threads and is expressed in mm units…

Q: In the 3% error, why is the design acceptable?

A: Given: There are 3% error in the design. And by this error the developed power reduced from 0.556 MW…

Q: Part C - Determining the displacement of a spring The cable segment attached to the spring is at an…

A: Given:- Part C:

Q: The block shown in (Figure 1) has a mass of m = 75 kg, a height H= 1.4 m, and width L = 1.9 m. It is…

A:

Q: Why should the selected section modulus, be slightly greater than Sreq>d?

A: Generally, section modulus is calculated by considering external loads only. So in order to account…

Q: What is the slenderness ratio?

A:

Q: 1)Draw three free-body diagrams of the beam supported at A by a pin support and at B by a roller…

A:

Q: Which material should be chosen when high strength is required

A: Given: To define: Which material should be chosen when high strength is required

Q: Determine (a) the horizontal and vertical components of the reaction that pins A and B exert on the…

A:

Q: what happened with the 10 in the first equation?

A:

Q: 2.4-4 A horizontal rigid bar ABC is pinned at end A and supported by two cables at points B and C. A…

A: given; P=10KN AD=1.5mAB=1.5mBC=1.5mAC=3mminimum cross sectional area of cable(A)=?yield…

Q: What are limits or limits of size?

A: This question belongs to Metrology. Metrology is a science of measurement by using different…

Q: calculate it manually and use your calculator to verify the manual calculation.)

A: Solution :- For part d Given :- The torque is given by the following vector product

Q: Expain about Poisson's ratio?

A: Poisson's ratio: "The ratio of lateral strain to the longitudinal strain is called Poisson's ratio."…

Q: BY y А Solve for the direction cosines and direction angles of vector A in above figure.

A:

Q: A heat source at 600 K loses 1000 kJ of heat to a sink at 300 K. The Entropy generated in this…

A: Write the given values with the suitable variables. T1=600 KQ=1000 kJT2=300 K Here, T1, Q, and T2…

Q: enumerate the 4 plate forming process and where it can be applied

A: given; enumerate the 4 plate forming process and where it can be applied.

Q: What are the Discontinuity Functions?

A: In Mathematics and Engineering, discontinuity functions are all those functions which are not…

Q: 1. Uf this drawing? 2. What is the name of the company responsible for the drawing? 2. MILWAVKEE…

A: Given :-  9.The drawings are shown in what angle

Q: Describe the method of sections?

A: Method of section In this method we deal with the non-concurrent forces. Here, we get three…

Q: So what are the correct answers

A: Explanation: If we consider a system that loses heat δQ at temperature T. Since, In this case the…

Q: what other manufacturing process steps may be required for the machined plate prior to use?

A: We have given a machined plate and we want to use it in another task. So for that purpose we have to…

Q: 2. A medium size power station is used to produce 30 MW net power for a refinery. The station uses…

A:

Q: 1. The pipe ABCDE is supported by ball-and-socket joints at A and D and by cable ECF that passes…

A: Given data: Find: (4) About which axis/line sum moments to generate an equilibrium equation with…

Q: How can you determine the Poisson's ratio?

A: Poisson’s ratio is ratio of lateral strain to longitudinal strain. When we apply tensile force on a…

Q: Determine the work of the force when displaces 2m. 500 N - 2 m (a) 98.1 N 2 m (b) 2 m F = (6x)N (c)…

A:

Q: the wind vane indicating the direction of the wind relative to the ship. After th ship changes…

A:

Q: 5. The following table shows joint position coordinates for the hip, knee, and ankle during a single…

A: Answer part (C): Given data: xknee=41.31yknee=22.87xAnkle=49.36yAnkle=9.03 Need to determine the…

Q: some examples about deep drwing?

A: deep drawing is a process in which complex shapes and seamless products are manufactured. A material…

Q: b) Use your own sketches to show how surface finish is measured and define 2 important parameters…

A: B) Surface finish is a characteristic of any machined surface. It is sometimes called surface…

Q: A homogeneous sphere S, a uniform cylinder C, and a thin pipe P are released from rest on the…

A: Calculated the running sequence of sphere, cylinder and thin pipe.

Q: Explain revision B?

A: As you can see in below image, at highlighted location, in revision B, there is diameter with upper…

Q: Engineering drawing Find, top section, side section and front section?

A:

Q: 7. (i) The engine of a car of mass 500 kg works at a constant rate of 15 kW. A non-gravitational…

A: (i) We are asked to solve only part (i) of the question. FBD diagram of the above system-

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.