During the measurement of a low resistance using a potentiometer, the following readings were obtained: Voltage drop across unknown resistance = 0.531 %3D Volts. Voltage drop across a 0.1 Ohm standard resistance connected in series with the unknown resistance = 1.083 Volt. %3D Value of the unknown resistor is (a) 49.03 milliohm (c) 20.4 milliohm (b) 108.3 milliohm (d) 53.1 milliohm

During the measurement of a low resistance using a potentiometer, the following readings were obtained: Voltage drop across unknown resistance = 0.531 %3D Volts. Voltage drop across a 0.1 Ohm standard resistance connected in series with the unknown resistance = 1.083 Volt. %3D Value of the unknown resistor is (a) 49.03 milliohm (c) 20.4 milliohm (b) 108.3 milliohm (d) 53.1 milliohm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

When a pure semiconductor is heated, it's resistance: a) goes down. B)changing every time. C) goes up. D) remains the same
Question #7 Find the voltage V at the junction of the diodes (marked as red). Assume all the diodes are ideal. 7V 1 k2 D1 1 k2 D4 Vo 1 k2 6V D2 9v D3 1 k2 -6V (a) 4V (b) 0V (c) 2V (d) 1V (e) -4V (f) -2V (g) -2.5V
11 R2 1K R1 D2 1K 5V D1 Determine the voltage across the resistor R2. (assume Zener voltage is 3 volts and Diode forward voltage is 0.7V) *
Which statement is not true about an extrinsic semiconductor? They do not have equal numbers charge carriers. Their impurities do not affect their electrical behavior. They can be doped with another element by a process known as doping process. They are chemically not pure. Their electrical properties can be tuned.
THK S1 R1 10K R2 1K OK R4 220R ww Q1 Figure 3-11. SCR as a Half-wave Rectifier. Vac 1. Place CM switch 1 in the on position which effectively changes the value of R1. What does this change do to SCR turn on? a. No change to SCR turn on. b. The SCR will turn on at a lower voltage. c. The SCR will not turn on due to insufficient gate voltage. d. There will be ten times more anode current.
I need help on this question and thank you
When a Ge diode is conducting at a temperature of 25oC, VT = 0.68 V. What is the VT at 106oC?
Determine and sketch the output voltage. R1 +10 V 1.0 kN D Vin 0 out 5v 5 v -10 V + Diodes are IN4001.
What is the current draw through the 1k resistor for this circuit? Why? 9.1V + ww 1kQ Signal Diode Zener Diode w/V₂ = 5.2
Solve letter b) I3 if all diodes are silicon diodes with VT=0.7V
Q1. Two diodes with Is1=10mA and Is2=20mA are used for the total reverse voltage barrier VR=1983V. If R1=50k ohm and R2=40OK ohm, calculate the voltage across diode 1 а-1324 b-992 c-879 d-1102 е-659
2. A bank of nickel-cadmium cells is used as the emergency lighting supply for a hospital. There are 100 cells connected in series and each has an A-hr rating of 120 A-hr. The bank has to be replaced, and the manufacturer is no longer supplying nickel-cadmium cells. It is decided to replace the cells with lead-acid cells. How many lead-acid cells will be required if each has an A-hr rating of 60 A-hr, and how should they be connected?