During a TIG welding process, the arc current and arc voltage were 50 A and 60 V, respectively, when in the welding speed was 150mm/min. In another process, the TIG welding is carried out at a welding speed of 120 mm/min at the same arc voltage and heat inputto the material so that weld quality remains the same. The welding current (in A) for this process is

Given, Current in process 1 = I1 = 50 A Voltage in process 1 = V1 = 60 V Welding speed in process 1…

Answered: During a TIG welding process, the arc…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Welding is a process that is used to attach pieces of metal to one another. In a certain welding process, small pieces of Al (s) and CuO (s) are placed in a crucible and ignited, causing the following highly exothermic reaction to occur. 2 Al+ 3 Cuo - 3 Cu + Al,O3 The copper and aluminum oxide melt. The molten aluminum oxide floats to the top of the crucible. When the steel disk below the crucible melts, the molten copper flows into the weld cavity and welds the pieces of metal together as it cools and solidifies. The setup is represented in the following diagram. Mixture of Al(s) and CuO(s) Crucible Steel Disk Weld Cavity Pieces of Metal to Be Connected
Using oxyacetylene welding method to weld a 3 feet long seam in a 3/8 inch thick plate at a consumption rate of 9 ft3/ft for oxygen and 7 ft3/ft for acetylene. What is the total combined gas consumption in ft3?
A gas tungsten arc welding operation is performed using a current 500 A and arc voltage of 20 V at a welding speed 10 mm/s. Assuming that the arc efficiency is 60 %. Determine the net heat input per unit length of the weld.
5. A steel cylindrical air receiver with 5 feet diameter and pressure load of 180 psi, design stress of 9500 psi maximum. The pressure vessel is to be provided with a 1.5 in diameter drain valve installed at the bottom of the vessel and a safety pressure relief valve is installed either at the topmost or at the side with a pop-out rating of 200 psi. Assume a 100% weld joint efficiency. The lap welding tensile strength is 65,000 psi. Determine the bursting pressure of this air receiver. psi
Your boss requests a recommendation on which process to use to weld the high strength structural steel rail tank cars hull section. You have this additional information: P-GMAW Productivity is substantially lower. However, you have welders already qualified to do manual p-GMAW welding. Labor is 80% of total cost HYPERFILLⓇ® Productivity gains are important, and the volume of the product is sufficient on the rail tank cars to justify capital investment. With confidence, you respond: Use process because .(Give process and short explanation for why you want to use that process)
22 Explain with sketches the dip transition technique in MIG/MAG. 23 Explain with details the types of flam in Oxy-Acetylene welding method.- 24: Explain with sketches the right hand and left hand technique in gas welding
A gas tungsten arc welding operation is performed using a current 750 A and arc voltage of 20 V at a welding speed 15 mm/s. Assuming that the arc efficiency is 80 %. Determine the net heat input per unit length of the weld.
A gas tungsten arc welding operation is performed using a current 700 A and arc voltage of 30 V at a welding speed 10 mm/s. Assuming that the arc efficiency is 80 %. Determine the net heat input per unit length of the weld.
An arc welding operation on nickel performs a groove weld, whose cross-sectional area = 20.0 mm2. The melting point of nickel Tm = 1725° Travel velocity = 4.0 mm/sec. Heat transfer factor = 0.82, and melting factor = 0.70. Determine the rate of heat generation required at the welding source to accomplish this weld.
A welding fabricator welds mild steel attachments to AISI 304 stainless steel shells, using GTAW with ER309L filler wire. A helium-based shielding gas (90% He-7.5%Ar-2.5%CO2) is used, but the high cost of this shielding gas is becoming an obstacle. To reduce costs,
During arc welding, the heat input per unit length reduces, with increase of
10)Which of the followings is true for LASER welding process? O It is a high heat input process O High reflectivity materials can be welded easily OA close control over process parameters is required for proper welding OVacuum conditions are required

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS