8) Consider the following statements regarding the Resistance micro-welding: A: Higher contact resistance is observed in resistance micro-welding compared to large- scale resistance welding. R: The electrode pressure is much lower in micro-welding. a. Both A and R are correct, and R is the correct reasoning of A. b. Both A and R are correct, and R is not the correct reasoning of A. c. Only A is correct, and R is incorrect. d. Only R is correct, and A is incorrect.

8) Consider the following statements regarding the Resistance micro-welding: A: Higher contact resistance is observed in resistance micro-welding compared to large- scale resistance welding. R: The electrode pressure is much lower in micro-welding. a. Both A and R are correct, and R is the correct reasoning of A. b. Both A and R are correct, and R is not the correct reasoning of A. c. Only A is correct, and R is incorrect. d. Only R is correct, and A is incorrect.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. What do you understand by the term welded joint? How it differs from riveted joint? 2. Sketch and discuss the various types of welded joints used in pressure vessels. What are the consider- ations involved? 3. State the basic difference between manual welding, semi-automatic welding and automatic welding. 4. What are the assumptions made in the design of welded joint? 5. Explain joint preparation with particular reference to butt welding of plates by arc welding. 6. Discuss the standard location of elements of a welding symbol. 7. Explain the procedure for designing an axially loaded unsymmetrical welded section. 8. What is an eccentric loaded welded joint ? Discuss the procedure for designing such a joint. 9. Show that the normal stress in case of an annular fillet weld subjected to bending is given by 5.66 M O = Lsd2 where M= Bending moment; s = Weld size and d= Diameter of cylindrical element welded to flat %3D %3D surface.
Describe FIVE (5) major hazards and precaution measures of Arc Rays and Spatter during performing Arc welding tasks that complies with OSHA requirements.
Which statements are correct? a. Hydroforming is typically used for composite body components b. Laser welding helps to decrease the load of the body c. fastening sequence of a body is 1st engine compartment, then facet panel then venter Od. In welding, for around 600 parts per shift robotised lines are preferred.e. Robogate is employed particularly for mobile parts welding. need the right answer , if wrong will downvote
8) The correct ways to control liquation cracking tendency in fusion weld joint are I. Use of filler metal that solidifies before the partially melted zone I. Use of single pass welding with higher net heat input instead of multipass welding III. Use of high energy density processes IV. Preheating the substrates V. Use of base metals with fine grain structure OI, II, and III II, and IV OII, IV, and V O II, III and IV
What percentage of a change are we allowed in travel speed when welding flux core? (number only)
2 A type of welding flows, which is the result of a perfect proportion and mixture of acetylene and oxygen and is used for fusion welding of steel and cast iron, is a. Neutral flame b. Oxidizing flame c. Carburizing flame d. Oxy-acetylene flame
5) The type of environment that offers best protection to the molten weld pool during fusion welding is Inert gas Vacuum Inactive gas O Molten flux
Which welding process is depicted? a. electron - beam welding O b. friction welding O c. resistance spot welding O d. ultrasonic welding O e. plasma arc welding
During a TIG welding process, the arc current and arc voltage were 50 A and 60 V, respectively, when in the welding speed was 150 mm/min. In another process, the TIG welding is carried out at a welding speed of 120 mm/min at the same arc voltage and heat input to the material so that weld quality remains the same. The welding current (in A) for this process is
Your boss requests a recommendation on which process to use to weld the high strength structural steel rail tank cars hull section. You have this additional information: P-GMAW Productivity is substantially lower. However, you have welders already qualified to do manual p-GMAW welding. Labor is 80% of total cost HYPERFILLⓇ® Productivity gains are important, and the volume of the product is sufficient on the rail tank cars to justify capital investment. With confidence, you respond: Use process because .(Give process and short explanation for why you want to use that process)
22 Explain with sketches the dip transition technique in MIG/MAG. 23 Explain with details the types of flam in Oxy-Acetylene welding method.- 24: Explain with sketches the right hand and left hand technique in gas welding
if a weldment is heated to correct distortion from welding, the maximum localized heat shall not exceed what temperature?