Due to Vs1 onlyDue to Vs2onlyTotalVAB'VAB (Vaa' + Vaa")In2'Ir2"Ir2 (Ir2' + Ir2")Table 21. Measure the voltage VAB' and current Ir2' due to Vs1 only (Replace Vs2 with a shortcircuit).2. Measure the voltage VAB" and current Ir2" due to Vs2 only (Replace Vs1with a shortcircuit).3. Calculate the total voltage and current by summing the two values togetherDue to Vs1 onlyDue to Vs2onlyTotalVABVag"VAB (Vaa' + Van")In2'Ir2"Ir2 (Ir2' + Ir2")Table 34. For the same Circuit measure VAB and current Ir2 without applying the superposition TheoremTotalVABIR2Table 4 Components Used:PartValuesRI22000R2600 QVsi6VVs23 VTable 11. Hand CalculationAnalyze the circuit in Figure 1. Perform Superposition Analysis, show your steps of calculations clearlyand record your values on Table 2Ir1R1Vs1Vs2Ir2R2

Answered: Image /qna-images/answer/71153b3b-1e3b-4117-9059-614aed751301.jpg

Due to Vs1 only Due to Vs2only Total Va Va VAB (Va' Van") Ir2" In2 (In2 + Ir2") Table 2 1. Measure the voltage VAB' and current Irz' due to Vs1 only (Replace Vs2 with a short circuit). 2. Measure the voltage VaB" and current Irz" due to Vs2 only (Replace Vs1with a short circuit). 3. Calculate the total voltage and current by summing the two values together Due to Vs1 only Due to Vszonly Total Vaa Vaa" VaB (Vaa' + Va") Irz" Inz (lnz' + Ir2") Table 3 4. For the same Circuit measure VaB and current Irz without applying the superposition Theorem Total VAB IR2 Table 4

Due to Vs1 only Due to Vs2only Total Va Va VAB (Va' Van") Ir2" In2 (In2 + Ir2") Table 2 1. Measure the voltage VAB' and current Irz' due to Vs1 only (Replace Vs2 with a short circuit). 2. Measure the voltage VaB" and current Irz" due to Vs2 only (Replace Vs1with a short circuit). 3. Calculate the total voltage and current by summing the two values together Due to Vs1 only Due to Vszonly Total Vaa Vaa" VaB (Vaa' + Va") Irz" Inz (lnz' + Ir2") Table 3 4. For the same Circuit measure VaB and current Irz without applying the superposition Theorem Total VAB IR2 Table 4

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Vdc0 U=12 V Circuit #1 Ried V LED www Ried_series 0.05 Vdc0 U = 12 V 0,04 Circuit 0.03 0.02 0.01 RED LED GREEN LE Set current to 10 mA LED voltages Given the circuit #1 presented above, answer the following questions: BLUE_LEC Red 0.5 1) Determine the value of the V₁ (voltage forward of the LED) for the LEDS RED, VDRED GREEN, VREEN and BLUE, VOBLUES when the current through the LEDs is 10mA, 2) Is the LED in Circuit #1, connected in the way that will be lighting up or not - Justify your answer Green 3) Calculate the value of the resistance Rled in Circuit #1, to ensure that a RED LED will have a current of 10 mA 1.5 2 25 Voltage across LED (V) 4) Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a current of 10 mA Blue 5) Calculate the value of the resistance Rled in Circuit #1, to ensure that a Blue LED will have a current of 10 mA 6) Given three LEDs, connected in series as shown in the Circui # 2 (below), calculate the value of the…
More five examples regarding this KCL method(with circuit figures and complete solution)
Five dry cells having emfs of 2.30, 2.40, 2.35, 2.60, 2.25 Volts and resistances of 0.40, 0.20, 0.35, 0.18, 0.32 Ohm, are connected in series to operate a lamp of resistance 12 Ohms. Determine current and power to lamp.
Q2: Define the component of Furnace temperature control system as a block diagram and the function of each unit
Reduction is the _______ of electrons. * gain t ransfer sharing loss
An independent current source while providing a fixed current having Select one a. Zero voltage across its terminals. b. Not applicable to measure voltage across it. C. None of the above. d. Unknown voltage acrosS ts terminals
What is the problem statement that can be found for "EFFECT OF VEGETATION ON V2V COMMUNICATION AT JUNCTION"
Special ProcedureIn figure 2.4 (same circuit as figure 2.1), using the Resistance Mode of the Multimeter,a. what is the measured resistance across terminals ‘c’ and ‘f’? Explain.b. what is the measured resistance across terminals ‘b’ and ‘d’? Explain.
Compared to the original circuit that it replaces, an equivalent circuit will always have:a. the same power dissipation.b. the same number of componentsc. the same voltage and current for a specific loadd. all of the above
What causes the normal heating in electronic devices? Not things that cause an anormal disfunction like dust or something else, but the one thing that by default creates normal heat in a system. I mean the actual part of the device which creates that heat.
State the characteristics of voltage and current in a series circuit connection of resistors. State the characteristics of voltage and current in a parallel circuit connection of resistors. please explain it properly.
Subject:Circuits INote:Support the problems with circuit diagram and label the pertinent partsPlease with full solution