D(s) Ks R(s) C(s) (5 K)s- (2 L)s (3 M)s C(s) =? (20P) K: Okul numaranızdaki rakamların toplamıdır (K: It is the sum of the digits in your school number). L: Okul numaranızdaki TEK rakamların toplamıdır (L:The sum of the ODD digits in your school number) M: Okul numaranızdaki ÇİFT rakamların toplamıdır (M: The sum of the EVEN digits in your school number) Ömeğin, okul numaranız 2010430568094 ise (For example, if your school number is 2010430568094) K-2+0+1+0+4+3+0+5+6+8+0+9+4-> K-42 olacaktır (K-42 will be). L=1+3+5+9-> L=18 olacaktır (L-18 will be). M-2+0+0+4+0+6+8+0+4> M-24 olacaktır (M-24 will be).

D(s) Ks R(s) C(s) (5 K)s- (2 L)s (3 M)s C(s) =? (20P) K: Okul numaranızdaki rakamların toplamıdır (K: It is the sum of the digits in your school number). L: Okul numaranızdaki TEK rakamların toplamıdır (L:The sum of the ODD digits in your school number) M: Okul numaranızdaki ÇİFT rakamların toplamıdır (M: The sum of the EVEN digits in your school number) Ömeğin, okul numaranız 2010430568094 ise (For example, if your school number is 2010430568094) K-2+0+1+0+4+3+0+5+6+8+0+9+4-> K-42 olacaktır (K-42 will be). L=1+3+5+9-> L=18 olacaktır (L-18 will be). M-2+0+0+4+0+6+8+0+4> M-24 olacaktır (M-24 will be).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

fast
What are synchro resolvers?
4- Determine the High-level noise margins for TTL circuits if VHCuain) = 2 V, VIL(max)=0.8 V. VoHmm)=2.4 V, VoL(mas) =0.4 V a- 0.4 V b- 1.2 V C- 1.17 V d- 0.7 V
Q29) The line encoder that uses three levels is---- a. None of the mentioned b. On-off c. Unipolar RZ d. RZ-AMI This multiple choice question from DIGITAL COMMUNICATIONS course.just write for me the final answer.
Question 13
The static error acceleration constant is both zero for system type 1 and 2. True or False
Please complete the expected timing diagram from the truth table.
Briefly explain how does static 1-hazard differs from a static 0-hazard. Assuming a propagation delay of 10ns for each of the gates given in Figure. 3, identify the type of static hazard (0 or 1) if there exists any. A timing diagram may help to find it out.
what are the two techniques for circuit switching? D) what is the cause of the propagation delay?
When the pinch-off voltage is exceeded, ID will ____ as VDD increases. remains the same double increases decreases
In which type of fault diagnosis the fault can be identified by PCB testing ? a. Replacement b. Physical Testing c. Half split technique d. Dynamic Testing