Draw the shear and moment diagram of the following beams. Determine the location and values of the minimum and maximum moments. Show your complete solution in a clean and organized manner on your worksheet

Q: QUESTION 3 For the beam show in figure 2, determine: (a) The reaction at the supports in term of the…

A: Given data P = 6 kn w=2kn/m

Q: The cross-sectional area of each member of the truss is 1200 mm² and the allowable stresses are 100…

A:

Q: The truss shown in Figure 1 is constructed such that members AB and BC are of equal length.…

A: A Truss ABC is given with 2 hinged supports at A and C, a point load of magnitude 12 kN applied at B…

Q: a b 4 m 4 m 12 kN 6@3 m = 18 m %3D

A:

Q: The force of a Truss is as follows. The E of all member sections is 30000 kips\in^2, and the A of…

A:

Q: 6. Calculate and determine what type of force acting on members AB, CE, and EF of the truss shown in…

A: Check for determinacy There are  3 nos of reactions possible in this structure, they are RH, HH and…

Q: Normal force, moment and shear diagrams and cross section given below according to their…

A: non circular soil section are torsionally week because shear stress distribution is non…

Q: 3m В G P E 3m C D

A:

Q: The rigid bar EFG is supported by the truss system shown. Knowing that the member CG is a solid…

A: Given Load PSpan 12 ftTo find out Normal stress in CG

Q: Use Virtual Work Method to answer the questions below considering the truss shown in the figure.…

A:

Q: Which of the following is NOT TRUE as an assumption in the elastic analysis of circular members…

A:

Q: Read the question carefully  Draw the shear force and bending moment diagrams including…

A: Solution Given Diagram

Q: Determine the forces in all bars of the truss in the Figure. If your solution is statically…

A:

Q: Problem 4. .- The figure shows a roof truss and the detail of the connection at joint B. Member BC…

A: Given data, τ = 75 MPa σb = 145 MPa Diameter of rivet = 20 mm

Q: Identify the maximum load intensity w0 that can be applied if the weld can resist a maximum shearing…

A: Compression strength means the material or structure's ability to resist loads that tend to decrease…

Q: Check the stability of truss.. Give me right solution with clear calculations.

A:

Q: a)Classify each of the beams shown below as statically determinate or statically indeterminate. If…

A:

Q: A laminated plastic beam of square cross section is built up by gluing together three strips, each…

A:

Q: Show complete solution (show how you achieve the member forces , e.g method of joints/method of…

A: Given : 2D truss solve using consistent deformation EI = constant

Q: Determine the forces in members EH and El of the double Fink truss (positive if in tension, negative…

A:

Q: Determine the force in members FG, BF, and CE of the truss shown in the figure below. Let P = 29 kN.…

A:

Q: Determine the force in each member of the truss. State whether the members are in tension or…

A:

Q: a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam…

A: 1-If Beam weighs 3600 N then drawing of SFD and BMD 2- if Beam Weighs is not know then finding of…

Q: All bar equal area =A All bars the same modulus of elasticity = E All bars the same coefficient of…

A: Bar BG is heated by 100 degrees centigrade, From Geometry it is clear that ∠AGB = 45° Axial force in…

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

A: Given, E = 30,000 ksi A = 1.25 in2  σ1 = 18 ksi

Q: III. By any method, solve the axial bar forces of the truss shown, and identify whet compression or…

A:

Q: Subject: Static of rigid bodies Find: Shear diagram of beam 1,2 and 3 with solution thank you!

A:

Q: 213. In structural practice, steel clip angles are commonly used to transfer loads from horizontal…

A: GivenForce,F=45kNDiameter of rivet=22mm

Q: the bars and truss have a cross section of 250mm^2. If thr maximum average axial stress in any bar…

A: Given :

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: The below structure is given; Where, P = 440 N

Q: The bell crack mechanism shown in Figure is in equilibrium for an applied load of F, = 15KN at A and…

A: Given: Bell Crank, F1 = 15KN, θ=65° Determine F2 = ?

Q: a) create a free body diagram of the truss and determine the external forces at the supports b)…

A: Solution-

Q: The bell crack mechanism shown in Figure is in equilibrium for an applied load of F, - 15KN at A and…

A:

Q: 2. CALCULATE THE FORCES IN ALL THE MEMBERS OF THE REINFORCEMENTS WITH THE METHOD OF THE KNOTS.

A: Calculation of vertical forcesVL + VR = 60 +50+40+20VL + VR = 170 KNConsider Moment equilibrium at…