Draw the phase diagram for each row on the table using the data and locate the phase on the phase diagram FIT, °C140155.46125300P, kPa361.535507501803V, m³/kg0.0350.0010970.0010650.140Phase descriptionSaturated mixtureSaturated liquidCompressed liquidSuperheated vapor

Answered: Image /qna-images/answer/1582f13f-2b3c-4981-80db-4347330a581d.jpg

Answered: Draw the phase diagram for each row on…

Engineering

Mechanical Engineering

Draw the phase diagram for each row on the table using the data and locate the phase on the phase diagram

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

It's not even that Idk how to do it, I'm very confused at that what parameters I should use to even begin answering. The initial masses of Ala dn Cu are 94.14g and 21.52g respectively
Use the phase diagrams for Cu-Ni and Cu-Ag systems below to answer the question: i. Wt% Ni in the liquid a Cu-Ni system at point B above.
Calculate the invariant reactions for Cu-Zn Reaction (eutectic eutectoid peritectic peritectoide) Temperature Transformation
Shown to the right is the solid-liquid phase behavior for mixtures of component A and component B at 1 atm. Use the phase diagram to answer the following questions. a) Specify the melting point of substance B at 1 atm b) What is the maximum composition (mole fraction) of component B that is possible for the mixture to exist in phase S2? At what temperature does this occur? c) 20mol of component A and 180mol of component B are mixed at 350°C and 1 atm. The mixture is cooled at constant pressure to 200°C. i) What phases are present at the final state? ii) What is the composition of each phase at the final state? iii) What is the number of moles of each phase at the final state?
What variable/s play a role in determining how and when phase transitions happen? (Check all that apply) Properties of the Material/Substance Pressure Temperature
100 atm 1 atm 0.118 atm 114 °C 184 °C 535 °C Temperature (not to scale) a.) Use the above generic phase diagram, clearly identify where you would find the following: Gas, Liquid, Solid, Triple Point, Draw arrows and label to indicate the six transitions (melting, freezing, sublimation, deposition, vaporization and condensation) b.) Based on the above phase diagram, what phase would you be in at a pressure of 50 atm and 300°C? c.) Based on the above phase diagram at what temperature in °C would vaporization occur under normal conditions? d.) If the pressure was 0.050 atm and 425°C, what phase would you be in? e.) If the pressure was 0.118 atm and temperature was 114°C, what phase(s) would you be in? f.) At approximately what temperature would the normal freezing point be in °C? g.) If the pressure was 0.105 atm and starting at a temperature of 32°C to 450°C what phase changes would occur (put in increasing temperature order). Pressure (not to scale)
help pls A two-phase phase diagram is shown. Answer the following questions t -1300 1500+ Temperature 1100 0 34 54! 166 482 80 Composition of Ni % 20 What is the composition (in % Cu) of the solid phase corresponding to the red dot in between the solidus and liquidus lines in the phase diagram? Just write the number. Do not write the % symbol. Question 17 2.33 100 An alloy is being made with 66% Ni and 34% Cu. When it is cooled from 1500°C to the temperature corresponding to the red dot in the phase diagram, how many kg of liquid is present in the mixture?
If 20000 g of steam is condensed in 2 x 10^6 cm³ at a pressure of 4 MPa a. What is the temperature (C)? b. In what state steam? c. Draw it in the form of a phase diagram that you know
Use the first image to solve two part question
4. For the A-B alloy the phase diagram below, use the lever rule to find the amount of liquid and solid states and their compositions at Temperature T. Let Cx = 25%B, C =40%B, Cy = 60 %B Complete solubility of two metals in liquid and solid states (Ni -Cu ,Sb - Bi) TA M EM T EMa T Cy A B Concentration of B in A www.substoch com Temperature
If 20000 g of steam is condensed in 2106 cm³ at a pressure of 6 MPa a. What is the temperature (C)? b. In what state (state) steam? c. Draw it in the form of a phase diagram that you know
how do you find the composition based on the tempratures from the phase diagram, like the temp are 160 and 130 right but you did both the temp above 150 in the phase diagram, also in the last line under given you wrote 35% sn and 55% sn, shouldn't it be 55% bi