Draw the influence lines for (a) the vertical reaction at A, (b) the shear at C, and (c) the moment at C. Use the Müller-Breslau principle. The image shows a horizontal beam supported by two structures labeled A and B. The beam is divided into sections with the following measurements:- The left section from the end of the beam to support A is 6 feet long.- The middle section between supports A and B is 6 feet long.- The section from support B to the point labeled C is 3 feet.- The final section from point C to the end of the beam is 3 feet.In total, the beam spans 18 feet. Support structures A and B appear to be evenly distributed under the beam, and point C is marked by an arrow indicating its location along the beam. This setup is typically used to analyze forces and moments in structural engineering.

Answered: Draw the influence lines for (a) the…

Draw the influence lines for (a) the vertical reaction at A, (b) the shear at C, and (c) the moment at C. Use the Müller-Breslau principle.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a. What are the external reaction at the position of the rocker at D, the external horizontal, vertical and resultant reactions at point A? [Solve for a value in kips, with right as positive and left as negative.] b. What is the force in member BC? c. What is the minimum possible diameter of the pin at A which is double shear and the minimum possible diameter of pin B which is single shear? [in inches]
The hoist supports the 150-kg engine. Determine the force in members DB and FB. Also determine the reactions on the floor at A and C. m m 2 m BO E 2 m 1m
1. Draw the influence line for member FC. Use the tabulation method. 2. A uniform live load of 10kn/m and a single live concentrated force of 35kn are to be placed on the beam. The beam has a weight of 38kn/m. Determine (a) the maximum vertical reaction at support B, and (b) the maximum negative moment at point B. Assume the support at A is a pin and B is a roller.
A concentrated live load of 15 kN and a uniform live load of 4 kN/m are to be placed on the beam. The beam has a weight of 1.75 kN/m. Assume the support at A is a roller and B is pinned. *C is not an internal pin. Determine the following: a. the maximum vertical reaction at support A b. the maximum positive moment at point C. B 10 ft 10 ft 15 ft
1. Determine the absolute maximum live moment in the beam due to the loading shown 8 KN 3 kN 4 kN B. 3 m 2m 12 m
Q2 Use the Müller-Breslau principle to sketch the influence lines for the vertical reaction at A, the shear at C, and the moment at C. D A C B E
Find the reaction at the simple support of the propped beam by using moment-area method. TITI L Wo THE TWO
Find the max compression on member DI in kN. Put "0" if none. a= 4.5m b= 4.8m c= 50kN d= 68kN
Use the Müller-Breslau principle to sketch the general shape of the influence line for the moment at A.
Obtain the reactions for the beam below E, and I are constant
For the truss shown in the figure below, assume that the loads are being transmitted to the bottom chord and draw the influence lines for member DI and EK. Also, considering the 3-point moving load as shown, determine the following member forces. Assume that the loads move only to the right. a. Maximum tension on member DI in kN, put “0” if none. b. Maximum compression on member DI in kN, put “0” if none. c. Maximum tension on membe EK in kN, put “0” if none. d. Maximum compression on member EK in kN, put “0” if none. a= 5.1 m b= 6.3 m c= 62 kN d= 78kN
Use the Müller-Breslau principle to sketch the general shape of the influence line for the moment at A and the shear at B.