Draw clearly the Kinematic diagram and the degree of freedom 100 N 40 mm 75 mm 55 mm 90 mm 60 65 mm 300 mm 100 N Bolt Cutter

Q: For the gear train in a watch shown in the following figure. The teeth number of each gear is…

A: Gear train Gear train is the mechanical system in which number of gears connected together by…

Q: i need a explanation what means the roll and count all nb of (link and j1 and j2) on the graph…

A: Step 1: In this image, a mechanical system with various links and joints is shown. there are three…

Q: In the belt drive system shown below, the input pulley is attached to an electric motor transferring…

A:

Q: What are the direction and speed of the driver gear (D1) in the figure below if the driven gear (D2)…

A:

Q: If arm 6 and gear 5 in the following figure are driven clockwise (viewed from the right end) at 150…

A: Given; The number of teeth on pinion, Zp = 24 The pitch of pinion, p = 6 The pressure angle, α = 20°…

Q: The figure below shows a four- par linkage. If a=5m, b=7m, =9m, d310m, 0=60°, p-10°, a=30° and…

A: Solution given,Q= 5m, b=7m, c=9m , d= 10m ,θ=60, ∅=10°W2= irad/sTransmission angle : Angle b/w…

Q: Find the gear ratios of given gear systems. zz=10 z-40 z3=7 z,=24 zs=14 z5=18 Giriş Z6 OUT Giriş Z6…

A: Gear ratio is defined as  Output/Input For the first case G.R.=(z2×z4×z6)/(z1×z3×z5)…

Q: Determine the magnitude of the velocity of block C at this instant.

A:

Q: Several forces act simultaneously on an eyebolt. Calculate the magnitude of the resultant force and…

A:

Q: 5.3' 4.5' 3' 3.5' 4.5' 5.3' 1' 6.8' 3.6' 5.5'

A: Draw a kinematic diagram of given mechanism.Identifying all joints and links also find DOF.

Q: Figure 0 4 m Q Search F > ▾ Part B. Part C Determine the angular impulse about point O for t = 4 s,…

A: t = 4 sec F = (4t+2)N

Q: A stepper motor is used to drive an x-y milling machine table. If the step angle of the motor is 1°…

A: Given, Step angle of the motor, α=1°Pitch of the lead screw,p=7mmSpped, V=25.0mm/sDistance moved by…

Q: Input shaft of the gear train shown below rotates at 1,500 RPM. The output shaft must rotate exactly…

A:

Q: c) Consider the mechanism in the next figure. The symbols r and / stand for the length of the link…

A:

Q: Problem The intermediate shaft in the two-stage gearbox shown below is to be designed. The…

A:

Q: Analytically determine the linear displacement of the piston in the compressor linkage shown in the…

A:

Q: 5. In the figure below, gear A is the first driver in the compound gear train. If gear A makes one…

A: given; ⇒number of teeth of of gear A(TA)=80T⇒number of teeth of of gear B(TB)=36T⇒speed of gear…

Q: A DC servomotor drives the y-axis of a NC milling machine table. The motor is coupled to the table…

A: First, we need to determine the distance to be covered in the y-axis. This can be calculated using…

Q: Bar AB has an angular velocity wAB = 6 rad/s. (Figure 1) Figure Itranscript Determine the velocity…

A:

Q: The planetary gear train shown in the image below has 16 teeth on the sun and 50 teeth on the…

A:

Q: Determine the velocity of block A if end B of the rope is pulled down with a speed of 9.0 m/s.…

A: Given that: Velocity at B is 9 m/s. It is required to determine the velocity of the block A.