Draw a sketch of a typical CL vs angle-of-attack curve and a CD vs CL curve, and show how increasing camber (by putting a flap down) would change these curves. (B) Draw the same curves, and show how using boundary-layer control or leading-edge devices would change these curves

Q: you are going to design high speed, luxury car with compact space *for engine placements. What type…

A: Straight-six engine; The straight-six engine (also referred to as an inline-six engine; abbreviated…

Q: What are some ways to make sure the proper codes are being posted when using CAM software?

A: Given CAM software To find Verify the actual codes with generated codes

Q: Example 3: Initially block A has a speed of 3 m/s as shown. D block B at t = 6 s. The coefficient of…

A: The relation between velocity and acceleration can be obtained easily if one can obtain the relation…

Q: 1) What is the CL? 2) What is the position of maximum camber?

A: NACA stands for National Advisory Committee for Aeronautics. In the problem, a NACA 5 digit code…

Q: What good does it do to preview a toolpath in a CAM system before the real program code is written?

A: In the realm of computer-aided manufacturing (CAM), the ability to preview a toolpath before…

Q: 7. What are the rotating wheel positioning parameters? What is the role of each? Why does the rear…

A: Wheel positioning is of the maintenance of automobiles. It is sometimes called breaking or tracking.…

Q: A wheel has traveled for 100 m with 50 rpm. If we want to convert the wheel into a spur gear with…

A:

Q: Give a full presentation on Cams

A:

Q: Imagine that you add belts that can be adjusted according to the weight of the patient with snap…

A: Given U shaped Product To find Test for belt

Q: Write the advantages of CAD/CAM and limitations of CAD/CAM.

A: CAD (Computer-Aided Design) and CAM (Computer-Aided Manufacturing) are two closely related…

Q: esign 1 Dwell at zero displacement esign 2 Dwell at zero displacement esign 3 Dwell at zero…

A:

Q: Summarize and discuss how to integrate Reverse Engineering (RE) and Additive Manufacturing & 3D…

A: Metrology is used to acquire 3D geometry data, and specialised software is used to transform and…

Q: What are 2 low friction methods of changing the directional rotation of a power axle 90 degrees?

A: Bevel gears are used for 90 degree rotation of the torque. But it seems that there are some issues…

Q: What is flexibility? Why there is a need of flexiblity in manufacturing system? Sketch elements of…

A: Solution:

Q: How can different types of cams be classified. Give examples for each type of cam

A: Cam is defined as a mechanical component that is used to drive the other component through a…

Q: Discuss the main advantages and disadvantages of at least 2 drive systems that can be used to drive…

A: The drive systems that can be used to drive camshaft are chain drive , gear drive and belt drive.

Q: Please can you explain how the concepts of the kinematics of rigid bodies are related to position,…

A: Introduction: A rigid body is a perfect representation of a body that does not deform or alter its…

Q: What is the differnce between KPI and camber in Automotive industry?

A: given; What is the difference between KPI and camber in Automotive industry?

Q: 3. Explain with sketches the different types of cams and followers.

A: A driver member known as the cam. A driven member called the follower. A frame which supports the…

Q: 1. What is meant by CAD term? Give some examples on the CAD software. 2. What is meant by CAM term?…

A: Given data: 1.CAD 2.CAM 3.CAD/CAM 4.Manufacturing.

Q: Design a disk(radial) cam that would satisfy the requirement of the follower. The follower is a…

A:

Q: Explain with sketches the different types of cams and followers.

A:

Q: How do you know whether the toolpath is correct before you write the code for it in a CAM system

A: The employment of software and computer-controlled gear to automate a manufacturing process is…

Q: NACA 24112 Chord c = 150 cm 1) What is the CL? 2) What is the %3D position of maximum camber?

A: Dear student, please find the attached solution.

Q: (c) You can paddle your cycle maximum three times per second. If the diameter of driver paddle wheel…

A: Given Data⇒ Speed of driver paddle is ω1=3timessω1=3revolutions Diameter of the driver paddle wheel…

Q: What is the function of data acquisition system in mechatronic system?

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: NACA 6412, Chord = 100cm 1) what is the maximum camber? 2) What is the position of maximum camber…

A: Given, Chore length (C) = 100 cm

Q: Compare and contrast various input devices in cad/cam sections.

A: There are various input devices in cad/cam. These are devices used for communicating with computer…

Q: ap down) would change

A: As we know that,Co-efficient of lift (CL)=0<CL<2Co-efficient of drag(Cd)=0<Cd<1Angle…

Q: 4 0.00 5 -0.60 6. -1.04 7 -1.20

A: Language second older polynomial equation: f(x) = x- x2 x-x3x1- x2x1-x3 f(x1) + x- x1 x-x3x2-…

Q: Do you want to see a comparison of the many varieties of dynamic rams in terms of their…

A:

Q: How are Gear ratio and Speed ratio related?  Are they equal to each other?

A: Gear ratio is the ratio of teeth on the gear to the teeth on the pinion. or the ratio of teeth on…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.