Answered: Discuss any two diversity techniques…

Discuss any two diversity techniques available in transmission network and With the aid of sketch discuss one of the modes of propagation in transmission system.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 6RQ

See similar textbooks

Related questions

Q: Given a bandwidth of 10,000 Hz (1000 to 11,000 Hz), draw the full-duplex ASK diagram of the system.…

A: Bandwidth: The maximum rate of transfer of data of a network cycle is at time related to the…

Q: Design a channel coding scheme to detect two or less errors for the m source (00, 10, 01, 11). Can…

A: Designing a channel coding scheme to detect two or fewer errors for the given message source while…

Q: A path in a digital circuit-switched network has a data rate of 1 Mbps. The exchange of 1000 bits is…

A: Here, we have to write solutions for the above questions.

Q: The differences between Frequency Division Multiplexing (FDM) and Time Division Multiplexing (TDM)…

A: Frequency Division Multiplexing (FDM) and Time Division Multiplexing (TDM) are two widely used…

Q: Synchronous and asynchronous transmission (presentation, comparison). Considering a baseband signal…

A: The ratio between the data rates (D1/D2) of two transmitted signals occupying the same bandwidth,…

Q: To what extent do you agree with the statement that "overlapping among subcarriers does not induce…

A: Answer: I agree with the statement that overlapping among subcarriers does not induce Inter Symbol…

Q: What are the benefits and drawbacks of bipolar coding schemes? Describe why NRZ coding is…

A: Bipolar: A variant of the RZ code is bipolar return-to-zero (BPRZ) secret writing, wherever the…

Q: Channel Capacity(C) was found to be 1.44 S/No where S represent signal power and No is the Noise…

A: Channel capacity(C) is the number of bits allowed through channel per second. For no information…

Q: If the signal at the end of a 6km cable has a power value of 2, if you knew that this cable loses…

A: Given length=6km loss=0.5dB/km

Q: differences between Propagation constant (β) and wave number (k)

A: differences between Propagation constant (β) and wave number (k)

Q: Q6: Suppose the carrier waveform illustrate below with assuming a group of 10 information signals xi…

A: ANSWER:-

Q: Problem 2 In a DSB-SC system, the carrier frequency is 5 kHz and the message signal is given by m(t)…

A: Answer: I have given answered in the handwritten format in brief explanation

Q: Create a diagram for color-coding of network code with pin code for the following

A: Straight Through: Pin Configuration:

Q: Consider an OFDM system in which 1000 subcarriers are each to be modulated at 1000 bits per second.…

A: OFDM system in which 1000 subcontractor modulations are per second at 1000 bits. (A) The…

Q: system with 192 subcarriers. The duration of the OFDM symbol including the cyclic prefix is 11.8 µs.…

A: lets see the solution.

Q: For data is transmitted over twisted-pair cable, you have these characteristics: A signal's power on…

Q: How does signal attenuation differ between coaxial cables and twisted-pair cables over extended…

A: Signal attenuation is a significant consideration in data transmission over extended distances.…

Q: Study the works of Shannon and Nyquist on channel capacity. Each places an upper limit on the bit…

A: Given: The works of Shannon and Nyquist on channel capacity should be studied. imposes a maximum bit…

Q: Suppose a signal travels through a transmission medium and its power is reduced to one-half. What is…

A: Solution

Q: irment in which the signal w

A: Q. is a sort of transmission impairment in which the signal weakens because to the transmission…

Q: A) Explain about Multiplexing and Demultiplexing and types of Multiplexing.

A: Actually, given question regarding Multiplexing and de multiplexing.

Q: Suppose a signal travels through a transmission medium and its power is reduced to one-half. What…

Q: Given a transmission rate of 1 Gbps and a propagation speed of 200m / μ sec , how many meters of…

A: Transmission Rate = 1 Gbps = 109 bits per second Propagation Speed = 200 metre / micro second = 200…

Q: In what ways might the study of telecommunications inform the study of data transmission? Do they…

A: Data transfer is considered as moving of data from one digital device to another digital device.…

Q: We would like to transmit information over a CAT-6 twisted pair cable with a bandwidth of 250 MHz.…

A: In communication systems, channel capacity is the maximum amount of information that can be reliably…

Q: Explain the concept of signal attenuation in long cable runs and suggest techniques to mitigate its…

A: Signal attenuation is a common issue in long cable runs, particularly in the field of electrical…

Q: A transmission channel between two communicating stations is made up of three sections. The first…

A: A transmission channel between two communicating stations is made up of threesections. The first…

Q: scuss the application of twisted pair cable. Why was coaxial cable chosen for digital data…

A: Lets see the solution.

Question

100%

Discuss any two diversity techniques available in transmission network and With the aid of sketch discuss one of the modes of propagation in transmission system.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

Explain the concept of signal attenuation in long cable runs and suggest techniques to mitigate its effects.
Suppose a signal travels through a transmission medium and its power is at the receiver is 53 Watt whereas the power at the sender was 86 Watt. Calculate the attenuation.
Consider an OFDM system in which 1000 subcarriers are each to be modulated at 1000 bits per second. Assume that each subcarrier is to be modulated using QPSK. (a) What is the symbol transmission rate? (b) How close can the subcarriers be spaced and still be orthogonal? (c) Assume that at least one subcarrier always carries QPSK symbols. What is the lowest data rate that can be supported by this scheme?
If the signal at the end of a 6km cable has a power value of 2, if you knew that this cable loses 0.5 dB per km (i.e. -0.5 dB/km), then the power of the signal at the beginning of the cable was ..............
Given a transmission rate of 1 Gbps and a propagation speed of 200m / μ sec , how many meters of cable are needed for a full duplex transmission link to have a minimum capacity of 1500 bytes?
The two questions are related
communication systems help pls
Consider an OFDM system with 192 subcarriers. The duration of the OFDM symbol including the cyclic prefix is 11.8 µs. Find the data rate, if the code rate is 1/2 and BPSK is used?
Create a diagram for color-coding of network code with pin code for the following: Straight Through Cross-Over
is a sort of transmission impairment in which the signal weakens because to the transmission medium's resistance.
A transmission channel between two communicating stations is made up of three sections. The first introduces an attenuation of 16 dB, the second an amplification of 20 dB and the third an attenuation of 10 dB. Assuming a mean transmitted power level of 400 mW, determine the output power level of the channel.
2. A path in a digital circuit-switched network has a data rate of 1 Mbps. The exchange of 1000 bits is required for the setup and teardown phases. The distance between two parties is 5000 km. Answer the following questions if the propagation speed is 2 X 10° m: a. What is the total delay if 1000 bits of data are exchanged during the data transfer phase? b. What is the total delay if 100,000 bits of data are exchanged during the data transfer phase? c. What is the total delay if 1,000,000 bits of data are exchanged during the data transfer phase? d. Find the delay per 1000 bits of data for each of the above cases and compare them. What can you infer?