Consider an OFDM system in which 1000 subcarriers are each to be modulated at 1000 bits per second. Assume that each subcarrier is to be modulated using QPSK. (a) What is the symbol transmission rate? (b) How close can the subcarriers be spaced and still be orthogonal? (c) Assume that at least one subcarrier always carries QPSK symbols. What is the lowest data rate that can be supported by this scheme?

Q: Given a bandwidth of 10,000 Hz (1000 to 11,000 Hz), draw the full-duplex ASK diagram of the system.…

A: Bandwidth: The maximum rate of transfer of data of a network cycle  is at time  related to the…

Q: the difference between QPSK and offset QPSK? 2) Five channels, each with a l00 kHz bandwidth, are to…

A: 1. the difference between QPSK and offset QPSK 2.Five channels, each with a l00 kHz bandwidth, are…

Q: A channel has a bit rate of 4 kbps and a propagation delay of 20 msec For what range of frame sizes…

A: The Answer is in Below Steps

Q: Assume that the data is transferred using 16PAM (16-level pulse amplitude modulation). How many bits…

A: ANSWER : The number of possible pulse amplitudes in analog PAM is theoretically infinite. Digital…

Q: The differences between Frequency Division Multiplexing (FDM) and Time Division Multiplexing (TDM)…

A: Frequency Division Multiplexing (FDM) and Time Division Multiplexing (TDM) are two widely used…

Q: Assume that the data is transferred using 16PAM (16-level pulse amplitude modulation). How many bits…

A: Note: As you have asked multiple questions, as per our policy, we will solve the first question for…

Q: Types of modulation in which a parameter of a sine-wave carrier signal is varied by a digitalsignal…

A: Type of Modulation : It is the transimitting the information from periodic waveform(carrier signal)…

Q: Four channels, each with a 150-kHz bandwidth, are to be multiplexed together. What is the minimum…

A: Bandwidth is a range of frequencies that a system can transmit data. It is measured in Hertz unit.

Q: Consider TDM-based circuit switching with 8000 frames per second and 32 time slots per frame. During…

A: Given that, Number of frames per second= 8000  Number of time slots per frame= 32 Number of bits…

Q: Ten signals, each requiring 3000 hz, are multiplexed onto a single channel using FDM. How much…

A: Here in this question question we have given Ten signals, each requiring 3000 hz.we are using FDM…

Q: distance between the two stations is 10000Km. There are two intermediate switches which A 100MB of…

A: The answer is given below.

Q: An 16-QAM modulator transmits data at the bit rate of 200 Kbit/s thorough an AWGN channel with PSD…

A: 3

Q: Multiplexing is done with TDM, FDM, and CDM on the physical layer. What are the pros and cons of…

A: Multiplexing is a technique used to transmit multiple signals over a single communication channel.…

Q: Five Channels each with a 100 KHz bandwidth are to be multiplexed together using Frequncy division…

A: Answer is.  The minimum bandwidth is 540 Khz.

Q: Study the works of Shannon and Nyquist on channel capacity. Each places an upper limit on the bit…

A: Given: Learning about the research of Shannon and Nyquist on channel capacity is essential. sets a…

Q: To what extent do you agree with the statement that "overlapping among subcarriers does not induce…

A: Answer: I agree with the statement that overlapping among subcarriers does not induce Inter Symbol…

Q: Ten signals, each requiring 4000 Hz, are multiplexed onto a single channel using FDM. What is the…

A: The answer is

Q: We need to transmit 100 digitized voice channels using a pass-band channel of 20 KHz. What should be…

A:

Q: We use modulation in communication system for many reason, one of the reason for using it in AM is:…

A: What is modulation?    Modulation is the process of encoding information from a message source in a…

Q: This problem considers the design of a Pulse Code Modulation (PCM) system. Assume that an analog…

A: Answer:- Average Signal to Noise power ratio in dB=49.92 dB Explanation:

Q: Six channels, each with a 200 kHz bandwidth are to be multiplexed using FDM together. What is the…

A: It is an analog technique that can be applied when the bandwidth of a link (in hertz) is greater…

Q: An analog signal is first encoded in binary PCM before being transformed to a multilevel signal for…

A:

Q: The correct matching of the given table is A 3500 Hz signal 1 ELF B 250 Hz signal 2 VLF C 350 MHz…

A: Match the correct answers.   Note: Kindly read the frequency range table mentioned in step 2, where…

Q: III. The figure below shows synchronous TDM, the data rate for each input connection is 1 Mbps. If 1…

A: ans given below

Q: Q4: An analog voltage waveform's information is to be sent with ±0.1 percent accuracy through a PCM…

A: ANSWER:-

Q: a signal remember the conversion!). What is the maximum data rate achievable? Explicitly mention the…

A: Given, Bandwidth of channel(B) = 2MhzSignal to noise ratio(SNR) = 40dB

Q: In synchronous TDM, it is possible to interleave hits, one bit from each channel participating in a…

A: Synchronous Time Division Multiplexing (STDM) assigns a fixed time slot to each connected device…

Q: Eight channels, each with a 4 KHz bandwidth are to be multiplexed together. What is the minimum…

A:

Q: Multiplexing is done with TDM, FDM, and CDM on the physical layer. What are the pros and cons of…

A: Multiplexing is a technique that allows multiple signals to be transmitted over a single…

Q: Suppose two users in a Direct Sequence-CDMA system have signatures (that is, sequences of chips)…

A: Actually, given question regarding CDMA.

Q: A channel has a bit rate of 4 kbps and one-way propagation delay of 20 ms. The channel uses stop and…

A: Introduction:Channel bit rate = 4 kbps1-way propagation delay = 20 msProtocol used = Stop &…

Q: A conventional amplitude modulator (AM), Vpc 5 volt is an offset voltage and c(t) is the carrier…

A: m = (Vmax - Vmin)/(Vmax + Vmin) where Vmax and Vmin are the maximum and minimum amplitudes of the…

Network transmission cabling

A network is a collection of devices connected by communication links. A device can be a computer or any instrument capable of sending and receiving data or information formed by other nodes toward the network. A channel that connects people or things is known as a network. It sends the data from one place to another. It is the basic concept of a computer, network, and data communications.