Discharging Capacitor In the circuit below, the time required (s) for the charge on the capacitor to drop to 37% of its value after the switch is closed is 0.8 s. If R = 750 ohms, what is C in μF (microfarad)? R +9 Submit Answer Tries 0/20

Discharging Capacitor In the circuit below, the time required (s) for the charge on the capacitor to drop to 37% of its value after the switch is closed is 0.8 s. If R = 750 ohms, what is C in μF (microfarad)? R +9 Submit Answer Tries 0/20

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter21: Circuits And Dc Instruments

Section: Chapter Questions

Problem 53PE: A 1,00-?O voltmeter is placed in parallel with a 75.0kresistor in a circuit, (a) Draw a circuit...

See similar textbooks

Similar questions

A circuit contains a D-cell battery, a switch, a 20- resistor, and three 20-mF capacitors. The capacitors are connected in parallel, and the parallel connection of capacitors are connected in series with the switch, the resistor and the battery, (a) What is die equivalent capacitance of the circuit? (b) What is the KC time constant? (c) How long before the current decreases to 50% of the initial value once the switch is closed?
An ECG monitor must have an KC time constant lessthan 1.00102s to be able to measure variations involtage oversmall time intervals, (a) If the resistance of the circuit (duemostly to that of the patient's chest) is 1.00kTwhat is the maximum capacitance of the circuit?(b) Would It be difficult in practice to limit the capacitance to less than the value found in (a)?
In this chapter, most examples and problems involved direct current (DC). DC circuits have the current flowing in one direction, from positive to negative. When the current was changing, it was changed linearly from I=ImaxtoI=+Imax and the voltage changed linearly from V=Vmax to V=+Vmax where Vmax=ImaxR .Suppose a voltage source is placed in series with a resistor of R = 10 that supplied a current that alternated as a sine wave, for example, I(t)=(3.00A)sin(24.00st) . (a) What would a graph of the voltage drop across the resistor V(t) versus time look like? (b) What would a plot of V(t) versus I(t) for one period look like? (Hint: If you are not sure, try plotting V(t) versus I(t) using a spreadsheet.)
Consider the circuit shown in the preceding problem. Write equations for the power supplied by the voltage sources and the power dissipated by the resistors in terms
Consider the circuit below. The capacitor has a capacitance of 10 mF. The switch is closed and after a long time the capacitor is fully charged, (a) What is the current through each resistor a long time after the switch is closed? (b) What is the voltage across each resistor a long rime after the switch is closed? (c) What is the voltage across the capacitor a long time after the switch is closed? (d) What is the charge on the capacitor a long time after the switch is closed? (e) The switch is then opened. The capacitor discharges through the resistors. How long from the time before the current drops to one fifth of the initial value?
A 50resistor is connected across the emf v(t)=(160V)sin(120t) . Write an expression for the current throug1 the resistor.
A defibrillator sends approximately 0.1 C of charge through a patients chest in about 2 ms. The average voltage during the discharge is approximately 3,000 V Compute the average current that flows, the average power output, and the total energy consumed (Note: Only a small portion of this current actually flows through the heart in a typical fibrillating procedure. Much of the charge is diffused throughout the patients thoracic cavity).
A 160F capacitor charged to 450 V is dischargedthrough a 31.2k resistor, (a) Find the time constant.(b)Calculate the temperature increase of the resistor, given that its mass is 2.50 g and its specific heat is 1.67kJ/kg °C,noting that most of the thermal energy is retained in the short time of the discharge, (c) Calculate the new resistance, assuming it is pure carbon. (d) Does this change in resistance seem significant?
Using your understanding of the nature of internal energy and temperature, explain why we might expect the resistance of a solid to increase if its temperature increases.
Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0 resistor, (b) Find the current in the 3.00-12 resistor.
Consider the circuit shown below. (a) What is the terminal voltage of the battery? (b) What is the potential drop across resistor R2?
Consider a circuit that consists of a real battery with an emf and an internal resistance of r connected to a variable resistor R. (a) In order for the terminal voltage of the battery to be equal to the emf of the battery, what should the resistance of the variable resistor be adjusted to? (b) In older to get the maximum current from the battery, what should the resistance variable resistor be adjusted to? (c) In order for the maximum power output of the battery to be reached, what should the resistance of the variable resistor be set to?