Directions: Observe the diagram below, write down the effects of hazard, and answer the questions that follow. Hazard House Type Effect of Hazard to House Type

Q: 2. Solve the problem using the member stiffness relationship in the global coordinate system, F =…

A: Step 1Write the expression for the stiffness coefficient, kij when i is row number and j is column…

Q: 3) You have a plot of land that measures 1850.53' x 2353.92'. How many square chains is this? 4)…

A: 3) The given area is shown below: 1850.53'×2353.92'

Q: 11. A police officer is checking the license and registration of the vehicles crossing a control…

A: Given:- The time taken by the officer to check vehicle = 2 min per veh After 45 min, second officer…

Q: Breaking strengths of a random sample of 21 molded plastic housing were measured, and a sample…

A:

Q: O A rectangular channel 1.30 wide carries 1.10 m/s of water at a depth of 0.85 m. If a 30-cm wide…

A: Equating specific energy of channel at both section to get elevation of water surface

Q: TANK TANK DATUM DATUM. DRAW AND LABEL VELOCITY HEAD DRAW AND LABEL PRESSURE HEAD (STATIC) Pressure…

A:

Q: xplain why the requirements of Australian Design Rules (ADR's), the National Code of Practice (NCOP)…

A: Solution: The Australian Design Rules (ADRs) are national safety, anti-theft, and emissions rules…

Q: List and define six hydraulic losses that occur in pumps.

A:

Q: Water is pumped through a vertical steel pipe to an elevated tank. D = 10 cm, P₁= 1.6 MPa, L = 80 m,…

A: Given data:- The given diameter, D=10 cm=0.1 m The given Pressure at 1, P1=1.6 MPa The given Length,…

Q: Answer the following service Engineering question. ( add reference and intext citation) Outline the…

A: Approach to solving the question: Kindly read with comprehension and I hope it helps :) Detailed…

Q: The three basic stages of construction planning are: (A) Preconstruction planning, post-construction…

A: Three basic stage of construction planning are: Pre conceptual planning Conceptual planning  Post…

Q: 20' A 26' B 25' Design a rectangular beam AB 25 ft simple span. fé= 3000 psi. fy=c = 60000 psi, NwC.

A: Span, Compressive strength of concrete, Yield strength of steel, Dead load, Live load, Width of…

Q: List two methods of hazard identification used in industries.

A:

Q: 3. Define the best efficiency point (BEP), allowable operating range (AOR), and preferred operating…

A:

Q: A wood structure is assembled to support the force applied. All pieces of wood have a width of 5 in.…

A:

Q: A reinforced concrete bearing wall supports a factored load of 650kN/m. It is laterally supported at…

A: Wall bearing factored load = 650 kN/m Unsupported height = 3500 mm Unsupported length = 3000 mm…

Q: Find the axial load resistance of the tied short column shown below and check all code requirements.…

A: b = 350 mm h = 350 mm fc = 30 MPa fy = 400 MPa Main bars, 8-20mm

Q: What type of bridge is this? Why is it called the type that it is? Explain how this bridge works. G

A: The given figure is a Steel Truss Bridge

Q: 7) A sharp crested weir is to be installed to measure flow in the range of 0.5 m³/s to 1.0 m/s. If…

A: Sharp crested weir: The weir in which the crest is sharp so that the water flows downwards and…

Q: Using the activity list below and any appropriate drawing tool, create a complete network diagram…

A: