Do fast The following data is given for anopen-type F-belt drive:diameter of driving pulley200 mmdiameter of diven pulley 600 mmgroove angle for sheaves34"mass of belt 0.5 kg/mmaximm permissible tension in beltcocfficient of /rictioncontact angle for smaller pullerspeed of smaller pulley500 N0.21571440 rpmpower to be transmittedHow many 1-belts shouldl be used, assuming10 RWeach belt takes its proportional part of the load?

Given that , N=1440rpm D=600 mmd=200mmθ=34°m=0.5kg/mP=10KWf=0.2αs=157°Tmax=500N

diameter of driving pulley 200 mm diameter of drivren pulley 600) mm groove angle for sheaves 34" (0.5 kg/m maximum permissible tensiom in belt 500 coefficient of friction 0.2 contact angle foor smaller pulle speed of smaller pulley 1440 rpm power to be trnsmitted 10KW mass of belt 157 How mamy 1-belts should be used, assun

diameter of driving pulley 200 mm diameter of drivren pulley 600) mm groove angle for sheaves 34" (0.5 kg/m maximum permissible tensiom in belt 500 coefficient of friction 0.2 contact angle foor smaller pulle speed of smaller pulley 1440 rpm power to be trnsmitted 10KW mass of belt 157 How mamy 1-belts should be used, assun

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4 A compressor requires 120 kW to run at 240 rpm from an electric motor of speed 750 rpm by means of a V-belt drivę. The diaincter of comp shaft pulley should not be more than 1000 mm while the center distance between the shafts is 2000 mm. Belt speed should not be more than 25 m/sec. Detcrmine number of belts to transmit the power it each belt has cross-sectional arca of 375 mm', density 1000 kg/m' and allowable tensile stress of 2.5 MPa. The pulley groove angle is 40° and coeff, of friction between pulley and belt is 0.25:
Help me please
2. Design a V-Belt drive, Specify the belt size, the sheaves sizes, the number of belts, the actual output speed, and the center of distance. Service Input Input Power Nominal Problem Driver Driven Турe Machine day speed output (HP) (kW) (rpm) speed(rpm) 1750 3.73 310 26 22 V-Belt AC motor Fan (NT)
Give/ Enumerate five applications of Grashof linkage in mechanical engineering and discuss how at least 3 to 5 sentence per application.
EFx=0= (0.433 F1) - (0.667 F2) - (0.866 F3) + (0.342 P) EFy=0= - (0.250 F1) + (0.667 F2) EFz=0= (0.866 F1) + (0.333 F2) + (0.500 F3) - (0.940 P) Find the magnitude of F1, F2, and F3
Which type of clutch/brake is depicted in the figure below? 10⁰ O A. Internal expanding rim clutch/brake O B. External contracting rim clutch/brake OC. Band-type clutch/brake O D. Axial clutch/brake OE. None of the above
arrow_forward Question PROBLEM The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V-belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=900N), coefficient of friction ų=0.3 4- the speed of large pulley.
The following particulars apply to an inclined belt conveyor: Length of conveyor (loading end to discharge end): 100 mSpeed of belt: 1,5 m/sAngle of wrap around driving pulley: 220 degreesCoefficient of friction between belt and driving pulley: 0,3 Mass of rock conveyed (mass flow rate): 300 t/hThe discharge end is 22 m higher than the loading end. The total friction is equivalent to a force of 6,5 kN in the belt at the head pulley. The efficiency of the drive is 90%. 4.2.1 Calculate the power of the motor. 4.2.2 Calculate the minimum tension in the slack side of the belt as it leaves the driving pulley
The following data are available for a belt conveyor design: 1. Conveyor capacity: = 1300 t/h; 2. Belt speed = 1.5 m/sec; 3. Conveyor height = 15 m; 4. Conveyor length = 175 m; 5. Mass of a set of idlers = 15 kg; 6. Idler spacing = 1.2 m; 7. Load due to belt = 25 kg/m; 8. Inclination angle of the conveyor = 10 deg.; 9. Coefficient of friction = 0.05; 10. Start-up factor = 1.5; 11. Drive efficiency = 0.90; 12. Friction factor = 12; and 13. Breaking strength loss factor = 0.80 Determine the following: (1) Belt tension, (2) Load due to idlers, (3) Minimum motor power; (4) Acceleration of the conveyor belt, and the (5) Belt breaking strength.
A 7,5 kW electric motor (star-delta start) running at the speed of 900 r/min is to drive a laundry machine, which operates 12 hours per day, by means of a simplex chain drive. The laundry machine must run at approximately speed of 308 r/min. Based on the space restrictions, the center-line distance is limited to 400 mm. Specify the length of chain (in mm) to be used as well as the exact center-line distance. Note that the form of lubrication used is TPYE 2.
ΕΧΑMPLE ) CALCULATE the transmitted power by aV. beltrunning over a pully of 60cm diameter at 200rpm The coffiecient of friction between the belt and the pully is (0.25),angle of contact is (160°) and the maximum tension is (250)N.The groove angle is 45.
Revert Done 4.a. Linearise the relationship between the force F and the rotational velocity N of a mechanical flyweight governor F-kN² at the operating point (F., No). 4.b. Calculate the absolute error due to linearisation e = | Flin Freal| at operating point (F. =4 N, No 200 rev/min) for N=250 rev/min. 0 G