Determine the volume in cubic meters of the borrow-pit given in the figure below. Corner cut heights are in meters

Q: a. For the particle size distribution curve shown below, what is the percentage of gravels, sand and…

A: Mark as shown above

Q: A steel wire 28 ft long, hanging vertically, supports a load of 698 lb. Neglecting the weight of the…

A: Please refer the attached image for complete solution. THANKYOU !

Q: Calculate the discharge in pipe 3, in m^3/s.

A: Step: 1 Head loss: - In fluid system, energy dissipated due to friction along the hydraulic system…

Q: 3) Explain the common properties of dense, uniform, gap and open gradations. What is the main…

A:

Q: The shear stress acting on the failure plane is O 100 -100 O 200 -200 Question 4 The normal stress…

A: Given:Required:Shear and normal stress on the failure plane

Q: They say that the 6 is the base 1 and the 7.6 is adding 6+0.8+0.8 as base2. My question is why you…

A: The expression which is shown in the solution is 12(6+7.6) here the values of geometry are…

Q: To be classified as hollow, the unit must have what percentage voids? a. between 25 and 60 b. >60 С.…

A:

Q: Exercise 3 Calculate the volume (cubic meter) of earth work in an embankment of length 15 m. The top…

A:

Q: ooper made up of aluminum given a dimension below will scoop a sand, what is the volume of the…

A: First we determine inside dimensions Thickness is given = 0.0020739 Outside dimensions are given

Q: Penetration 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Penetration (mm) 2 4 6 8 10 12 Load (KN) 2 4 6 8…

A: The CBR test was first developed in California, USA, to determine the bearing value of highway…

Q: A stone is fully submerged in water. It weighs 450 N in air and 200 N in water. Calculate the volume…

A:

Q: use three decimal places Derive hf with respect to Q of the following empirical equation below.…

A: For the Hazen William's formula -  Given - V = 0.849 C R0.63 S0.54 As known -  Q = VA here, Q =…

Q: Problem 1: Moody's Diagram - Finding the Friction Factor Value You perform a calculation for the…

A: Given data- Reynold's Number- Re=2.5×105, e/D ratio = 0.0002, To Find- The value of friction factor…

Q: Marshall sample is compacted at 75 blows. * O True O False

A:

Q: 1- Gate OA is a mass of (200+x) kg, Gate OA is 2m wide into the paper, Yeycerin=12000 N/m3…

A: unit weight of water = 10,000KN/m3

Q: 2. The masses of the blocks are ma = 30 kg and mg = 70 kg. Between all of the contacting surfaces,…

A:

Q: Problem A sample of a dry coarse grained material of 500 grams was shaken through a nest of sieves…

A:

Q: A vector, F , has components F=-286.9 N and Fy = 410.6 N. What is the angle made with the…

A:

Q: Find the solution(s) for a triangle with C = 38.65°, a = 17.87cm, b = 26.40cm Round your answers to…

A:

Q: V V V V V VV ↑

A:

Q: A cast iron pipe having a diameter of 100 mm is used to fill the cylindrical tank with water at T =…

A:

Q: 2. A subtense bar has a length of 2m measured by theodolite. Determine the values of D. A1 = 04 80’…

A:

Q: 2.A cylindrical sample with a circular cross section is given a load as shown in Figure 2 with the…

A:

Q: 11 The following are the results of a consolidation test on a sample of a clayey soil. 11.3…

A: a)e-log p graph is drawn excel shown below

Q: 4. solve the following system by using Jacob's Method with initial value x = y = z = 0. 5x + 2y + z…

A: Note -Since we answer one question at a time so we will answer the first one. Please resubmit…

Q: How can you get the pan encircled below? weight of sample = 1250g

A: Given data in question  Weight of sample Sieve sizes Weight retained To find out  Pan data

Q: 8. RISE AND FALL MRTHOD. Using the rise and fall method, complete the level notes given below and…

A: We will tabulate the table and then apply arithmetic check.

Q: Use Gauss-Seidel iteration to solve: (Do only ten iterations) 2х + у + 4z %3 6 5х + 2у — 2z %3D16 х…

A:

Q: The back fill material for a vibroflotation project has the following grain sizes. D10 0.11 mm…

A: Find sorting coeffficient

Q: If P = 1500 N and 0 = 40° Determine magnitude of the friction force. 1.2 kN| H, = 0.35 H =0.25 P…

A:

Q: In Ralston's Method, az is equal to O 1/3 O 1/2 O 2/3 O 3/4

A: this question is from ralston method  in this question we are asked to find out parameter a2

Q: An analysis damage of bridge structure at 1m to 3m length can be defined as a cubic spline function…

A: Construct in the natural cubic spine that passes through the point…

Q: B. Field Density Determination Volume of hole = 1900 cc Weight of dry soil from hole (field) = 2600…

A: Since you have posted questions with multiple sub-parts, we will solve the first three sub-parts for…

Q: Hydraulic Radius Determine the general expression for the hydraulic radius of a circular pipe…

A: It is asked to determine the expression for Hydraulic Radius of a circular pipe when it is fully…

Q: Situation 14: A sample of dry coarse-grained material was shaken through a nest of sieves and…

A:

Q: R200 300 500 500 300 R500 008

A:

Q: 3.5 Refer to Figure P3.1. Given that a₁ = 30°, a2 = 45°, a = 2m, a1 =3m, a2 = 5m, b = 2m, q1 =…

A: To find: Increase in vertical stres at M and N.

Q: The u and v axes pass through the centroid C of the rectangular area. Suppose that a = 200 mm.…

A: Solution given in next step

Q: then the total displacement

A: FALSE

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.