Determine the value VPc in m2Determine the value of heigt in 1+1800Determine the value Vp Two cross section is having the same base of the roadway which is 6 meters long. Point A in Station 1+800 ishaving 188m2 area with 1: 1 side slope. The illustration of cross section at point A is below:1.50h0.5h3m3m0.5hThe cross section of point B at Station 1+980 is:6.00+1.50.00+1.508.00+2.50Determine the value of Vpc in m2.

Data given station in point A = 1+1800 side slope = 1:1

Answered: Determine the value

Engineering

Civil Engineering

Determine the value

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The tangent vertical alignment of a section of proposed highway is shown in the figure below. Determine the vertical clearance (ft) between bridge structure at Station 23+00 and the vertical curve.
For a proposed highway curve with a radius of 500.00 meters, the point of curvature (PC) or beginning of curve station 10+00.00 and the point of tangency (PT) or end of curve station 14+00.00. The definition of station is 1 station = 100 meters. The CHORD length from the PC to the PT is %3! 1) 402.22 meters 2) 397.34 meters 3) none 4) 400.00 meters 5) 399.17 meters
Assignment 3: Vertical Curve Design Question 2 The reduced level at the intersection of a rising gradient of P % and a falling gradient of Q % on a proposed road is XX.XX m. Given that K value is KK. The throught chainage of the intersection point is YYYY.YY m and proposed vertical curve is to have equal tangent. As a civil engineering you are required to prepare the following vertical curve design calculations: a) The through chainage of the points of the vertical curve if the minimum required length is to be used (Lv) and the vertical curve setting out data at 20 metres interval. b) The chainage and reduced level of the highest point on the curve. c) Through chainage at highest point was located exactly under a bridge, if the RL of soffit is SS.SS m, calculate the headroom based on proposed vertical curve design.
Determine the height h in meters of the 400m2 cross section at Station 1+180 if the base of the roadway is 18meters and having a 2 : 1 side slope.
In (Figure 1), a single circular highway curve (arc definition) will join tangents XV and VY and also be tangent to BC. a) Calculate R and L. b) Calculate the station of PC. c) Calculate the station of PT.
Clean handwriting with diagrams answer three decimal places
This question about Transportation Engineering
A -1.10% grade meets a +0.60% grade at station 36+00 and elevation 800.00 ft. The +0.60 grade then joins a +2.40 grade at station 39+00. Determine the elevation at the low point of the curve. Express your answer in feet to six significant figures. 15. ΑΣΦ Elev = Submit Part B Request Answer Determine the station at the low point of the curve. 35+40.763 36+44.763 38+42.763 vec 36+42.763 D ? ft
if the TS is 23+20.25 what is the station the tangent runout begins ? Given a four lane roadway with a 50 mph travel speed, thatis entering a spiral curve and han a design max superelevaton of 4 0% he TS 23-20 25 what is the saton the langent nunout begins? (enter the h sation with sign, example, enter as 15-35 75)
The intersection of two proposed tangent AB and CD are inaccessible. From point G which is at Sta 10+266 on Tingent All The line GH is run to the point Fonn the Tangent CD The angle between the prolongation of AB and the line GH as measured by the transit is found to be 37 degrees. The line GHK measured and found to be 134.50 m and the angle between GH and the prolongation of CD is 24 degrees. It Tangent AB and CD are to be connected by 5 degrees. Find the STA of PC.
Two straight roadways AB and BC intersect at B with a deviation angle of 12°00'00". They are to be joined by a circular curve of 500 m radius from A to C. The curve is to be set out at 20 m chainage intervals, from point A. Given that the chainage of point B is 842.750 m, calculate: the chainage points of the setting out pegs along the curve (set out clearly in a table); the tangential angles required to set out the curve from the initial tangent point in degrees (") minutes (') seconds (").
show complete solution.