Determine the value of the summation of  x2 and y2 distances in mm2  and the value of torque in KN-mm  that the system of bolted connection will resist if rivet A and D were not properly driven that they do not carry any load and P=85KN

Q: When engineers design belt drives and band brakes, they engineer them to withstand the frictional…

A: GivenmA=49kgμA=0.300μB=0.320d=0.250m

Q: Problem 4. For the belt drive shown below calculate the contact angle 0, if: D = 100 mm; d 3 30 тm;…

A:

Q: Solve simultaneously Torque Equations 8.1 and 8.2 to find W1 and W2.

A:

Q: stone crusher machine working 8 hours a day is driven by an electric motor with a narrow-V…

A:

Q: following figure shows a belt braking system operating on a brake drum for a lifting mechanism. It…

A:

Q: Find the torque that must be applied to the limb numbered 2 in order to keep the crank-connecting…

A: Torque = 256.62 N-m

Q: Q 16- Find the length of a belt necessary to drive a pulley of 80 cm diameter running parallel at a…

A: Diameter of driving pulley, D1=480 cm=4.80 mDiameter of driven pulley, D2=80 cm=0.80 mDistance…

Q: Ki ke Ks Ks ka शान शि दा ////// गया

A: GIVEN DATA- A SPRING MASS SYSTEM GIVEN WE HAVE TO FIND EQUIVALENT SPRING STIFFNESS AND NATURAL…

Q: The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley…

A: diameter of pulley (d) = 110 mm  no of belt = n = 2 groove angle =  2β = 45° = β = 22.5° power…

Q: ne man and load in Prob. 5-17 he beam in Prob. 5-18. 5 kN 2 m 6kN

A:

Q: is it okay to solve this even if it is not in equilibrium? Why?

A: Solution:

Q: or the spring system given in Figure 1, create the element matrices as well as the global stiffness…

A: here, the force is determined by F = Keq x  so there is two spring in series  Hence  both are in…

Q: A race car is turning (cornering) on a flat road, as shown in Figure Q1-1. The speed of the car is…

A: Given Data- 1. Speed of car  v=300km/h 2. Turning radius  r =260m 3. mass          m   =890Kg (57%…

Q: A local utility vehicle production company have considered using in one of its design a multi-disc…

A: Given data:- steel discs=9 bronze discs =8 outside diameter =220mm inside diameter =160mm Shaft…

Q: The machine is designed to be powered by a 100 HP electric motor at a speed of 1500 rpm, with…

A: Given : P = 100 HP N = 1500 rpm d = 101.6 mm D = 406.4 mm L = 123.3 inches = 3131.82 mm To find :…

Q: The figure below shows two plates connected by two rivets. The plates are made from aluminum 6061-T6…

A:

Q: 1. Calculate the degree of freedom of the following mechanism shown in Fig. 4-1. If there are…

A: For the given mechanism  To determine  degree of freedom of the mechanism

Q: What is the maximum magnitude of the torque about the x axis caused by force F? If none, enter zero.…

A: It is needed to determine the maximum torque that is created by force F about the x-axis.

Q: A belt drive is used to transmit power from an electric motor to a compressor for a refrigerated…

A:

Q: Problem 1 A 48-in boom is held by a ball-and-socket joint at c and by two cables BF and DAE; cable…

A: .

Q: spring is to be inserted with an initial compression to produce a force equal to 125 N between the…

A:

Q: leafs spring contains 4 full-length and 8 graduated leafs. The eyebolts at the support are 20 inches…

A:

Q: A series of three links is given with lengths of 2.4 ", 7.2" and 3.4 ", select the length of a…

A: As per Grashoff law : The sum of the longest link and the shortest link should be less than the sum…

Q: The spring clamping force Fs = 2 N. The contact pressure force FA and the joint forces FB at the…

A: To Find : The contact force FA and FB for the toggle mechanism. Given : The spring clamping force is…

Q: Find the number of full joints and the degrees of freedom for the mechanism below, in which ABC is a…

A:

Q: b d

A:

Q: two cylinders are connected to form a parallel cylinder actuating system. Assume the bore and rod…

A: Given,For left cylinder-dl1=120mmdl2=60mmml=750kgPbpl=200KPaPlf=550KPaFor right…

Q: The gear forces shown act in planes parallel to the yz plane. The force on gear A is 300 Ibf.…

A: GivenForce at gear A, FA=300 lbf  parallel to y-z plane Factor of safety (n)=3.5 yield strength =60…

Q: -Find the factor of safety of the post BD using the langer-static criterion, Draw the the langer…

A: Here are the steps needed to use the Langer-static criterion to determine the post-BD safety…

Q: 5. For the engine-transmission-propeller problem shown below, The engine generates a torque of…

A: Transmission ratio,

Q: The specifications for a coil spring are known. Infinite fatigue life is required, using a safety…

A:

Q: Two 400 mm diameter pulleys are keyed to a simply supported shaft 500 mm apart. Each pulley is 100…

A:

Q: 3-17: A part for a truck suspension system is to carry a compressive load of 135 kN with the…

A: Given data as per question Compressive load = 135 KN

Q: Establish the relationship, to define the torque pairs to which the segments "AB" a subjected. VT B…

A: When two shafts are connected via a series combination, the equivalence torque remains the same,…

Q: The picture shows the rear swivel axle bearing design of a 4-wheel wagon. It is known that the speed…

A: Axels are shafts that are used to rotate the wheels. Its function is to transfer power from the…

Q: The required information is in the attachment.  Part A) Draw a free-body diagram. Show the torque…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.