Determine the total active force acting on the wall considering 1m width. (kN) b. Determine the location of the resultant force from the bottom. c. Compute the total active force if a surcharge of 20 kPa is applied on top of the backfill considering 1-meter width. (k

Determine the total active force acting on the wall considering 1m width. (kN) b. Determine the location of the resultant force from the bottom. c. Compute the total active force if a surcharge of 20 kPa is applied on top of the backfill considering 1-meter width. (k

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A water tank, 22 ft in diameter, is made from steel plates that are ½ inch thick. Find the maximum height to whichthe tank may be designed if the stress of the wall is limited to 1 ksi. Assume that the pressuredistribution varies linearly.
For the given retaining wall as shown, determine the following: Note: The water table for the given soil profile is located at an H1 depth below the top of the wall. 9. = 18 kPa %3D Ya = 18 kN/m³ O =25° H = 3 m %3D %3D II, = 4,5 m Yvar= 19.5 kN/m3 %3D o'= 30°
Investigate the resistance of the wall, whose dimensions and floor properties are given in the figure, against overturning and sliding, based on the 1.5 safety factor. Note1: Evaluate as Pp-0. Note2: Take the kive k coefficients as 2/3. |g=150 kN/m² c=0, 0-30° Vosted 24 kN/m³ X=18 kN/m³ 6 1m 1m 0.5m 3m
Question 01. For the concrete gravity wall shown below: a. Determine the magnitude, direction, and sense of the resultant force./ b. Determine where the resultant intersects the base of the wall with respect to point A (horizontally)./ 2 m 70 kN 1 m 6 m 53 kN 21.0 kN 2 m 1 m 4.5 m
2) For the following beam a. Draw the shear and moment diagrams of the beam. b. Determine b if the maximum allowable bending stress is 45 ksi Determine b if the maximum allowable shear stress is 12 ksi C. 10 k 2 k/ft 8' 10' 0.5 in thick wall b + 3b 30 k-ft
Compute for the following: a) The total active force on the wall in kNb) The total active moment at the bottom of the wall in kN-mc) Required passive force to maintain equilibrium in kNd) Theoretical passive force in kNe) total theoretical passive moment at the bottom of the wall in kN-m
!!!Show Complete Solutions and FBD!!! What is the bending stress in the beam 1.8 meteres from point A?a. 9.60Mpab. 8.60Mpac. 7.68Mpad.10.24Mpa What is the bending stress 20 mm from the top of the beam 1.5 meters from point A? a. 9.247Mpab. 7.225Mpac. 10.442Mpad.4.838Mpa What is the shear stress in the beam at point A?a. 0.48Mpab. 0.33Mpac. 1.57Mpad. 0.80Mpa
Problem 4. The gate below is 1.5 m wide and hinged at point B. It rests against a smooth wall at point A. Compute (a) the force on the gate due to the pressure of the seawater (specific gravity is 1.025 at 25°C), (b) the horizontal force, P, exerted by the wall at point A, and (c) the reaction at hinge, B. 4.5 m Р atmos Sea- water Gate ↑ 1.8 m B 2.4m P
Which are the Wall movements that produce the active and passive pressure conditions. Describe about them.
Give me right solution
10.37 FLUS Water (20°C) flows in a 16-cm cast-iron pipe at a rate of 0.1 m/s. For these conditions, determine or estimate the following: a. Reynolds number b. Friction factor f (use Swamee-Jain Eq. (10.39) in §10.6.) c. Shear stress at the wall, To
SITUATION 1| The system below is consisting of two solid circular cross-section bars AB and BC, joined as shown, and altached to a rigid vertical wall at the left. The system is subject to a concentric exial tensile force of 250 kN at C, together with an axisymnetric ring-type load applied at B having a horizontal resultant of 900 kN. For AB, E=110 GPa, and for BC, E=200 GPa. SOD 1200 900 250 1. Determine the maximum stress on member AB. 2. Determine the deformation of member AB. 3. Determine the overall deformation of the system.