Answered: Determine the thickness of a steel air…

Determine the thickness of a steel air receiver with 30 in. diameter and pressure load of 120 psi, design stress of 7200 psi. C. 5/8 in. D. 1/2 in. A. 14 in. B. 3/8 in.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter6: Fasteners

Section: Chapter Questions

Problem 14RQ: Hollow rivets are assembled in a pin that is often called A. a mandrel. B. a nozzle. C. an anchor....

See similar textbooks

Similar questions

Determine the thickness of a steel air receiver with 30 inches diameter and pressure load of 120 psi with a design stress of 8,000 psi. A. ¼ in C. 3/8 inB. 5/8 in D. ½ in
Calculate the wall thickness required for a thin-walled cylindrical pressure vessel which must withstand an operating internal pressure of 3.5 MPa at an outside pressure of 2 MPa. The mean diameter is 200mm and the stress must not exceed 60 Mpa. O a. 8.3 mm O b. 2.5 mm O c. 3.3 mm O d. 5.83 mm O O
The work cylinder of a hydraulic system is acted by a hydraulic pressure of 400 psi while the maximum load of the piston is 6000 lbs. if the allowable tensile stress is 2300 psi, what is the required wall thickness of the cylinder. a.0.510 in. b.0.448 in. c.0.420 in. d.0. 512 in.
Calculate the wall thickness required for a thin-walled cylindrical pressure vessel which must withstand an operating internal pressure of 3.5 MPa at an outside pressure of 2 MPa. The mean diameter is 200mm and the stress must not exceed 60 Mpa. O a. 5.83 mm O b.8.3 mm Oc 3.3 mm Od.2.5 mm
please answer number 2 with complete solution and box the final answer.(Use 4 decimal places for all computation).
5. Which area of the aircraft is subjected to hoop stress? Wings Control Surfaces а. b. Engine Cabin C. d. 6. The stresses experienced by aircraft during take off and landing are the same 7. It describes how well the substance can be hammered into sheets Toughness Malleability Ductility а. b. С. d. hardness 8. Wing mounted podded engines and integral fuel tanks Reduce the visibility of the passengers Provide increased safety if the undercarriage collapses on landing Reduce tailplane down load Provide wing bending relief A. В. C. D. 9. Which of the following choices is true about box beams? () closed section box beams is used in aircraft wings (ii) closed section box beams is capable of resisting torsional loads A Both (1) and (ii) are false Both (i) and (ii) are true and (ii) is not the correct reason for (i) (1) is true but (ii) is false Both (i) and (ii) are true and (ii) is the correct reason for (i) B
set c
a. Compute the tensile strength of the connection due to bearing failure of bolts.b. Compute the tensile strength of the connection due to shear of failure of bolts.c. Compute the tensile strength of the connection due to tearing of angular section.d. Compute the allowable block shear strength.e. Compute the allowable tensile strength of the connection.
The pressure in a cast-iron water pipe is 180 psi. If the inside diameter of the pipe is 15 in. and the allowable unit stress in tension is 2000 psi, what should be the thickness of a shell of the pipe, expressed as a multiple of 1/8 in. A. 3/4 in. B. 5/8 in. C. 1/2 in. D. 3/8 in.
8. An acetylene tank consists of a cylindrical body flat at its base and a hemisphere at the other end. The thickness of the metal used in this tank is 2 mm. The tank has a diameter of 250 mm and 1200 mm long. What is the internal allowable stress of the material is 180 MPa? a. 3.5 kPa b. 6.8 kPa c. 4.2 kPa d. 5.5 kPa
All dimensions in mm. All dimensions in mm. Fig. 9.37 Fig. 9.38 100 kN size shov 80 fina the diameter of the rivet. [A 18. A bracket in the form of a plate is fitted to a column by means of four rivets of the same size, as shown in Fig. 9.39. A load of 100 kN is applied to the bracket at an angle of 60° to the horizontal and the line of action of the load passes through the centre of the bot- tom rivet. If the maximum shear stress for the material of the rivet 80 80 60° is 70 MPa, find the diameter of rivets. What will be the thickness of the plate if the crushing stress is 100 MPa? [Ans. 29 mm; 1.5 mm] All dimensions in mm. Fig. 9.39
A tensile load of 330,000 N is applied to a copper pipe with maximum allowable stress of 110 MPa and 80 mm inner diameter. What should be the thickness of the pipe? Choices: A. 9.78 mm B. 12.35 mm C. 11.56 mm D. 10.55 mm