Determine the tensile stress in each cable given that all the cables have a cross-sectional area of 4cm?. Take mass of cylinder = 60kg; and acceleration due to gravity, g = 9.81 ms?. 45° B D

Q: 0.25 in. 5 in. 1 in. 0.25 in. -0.25 in. 2.5 in.

A: Maximum axial force P that can be applied to the steel plate

Q: The 4.00 m boom is uniform and weighs 2550 N. Find the tension in the guy wire and the force exerted…

A: The system of external forces remain in equilibrium only when all the internal and external forces…

Q: True or False: A cylindrical rod with a cross sectional area of 0.1 m^2 which is subjected to a…

A:

Q: A 100 N picture hangs from a nail in the wall. The diameter of the nail is 3.00 mm. The shear stress…

A: Write the given values with the suitable variables. F=100Nd=3 mm=3×10-3 m Here, F is the force and d…

Q: The cross-sectional dimensions of the beam shown in the figure are a = 5.0 in., b = 5.5 in., d = 4.6…

A: Concept: To determine the Maximum Tension and Compression Bending Stress we will divide the Cross…

Q: Asolid copper cube has an edge length of 85.0 cm. How much stress must be applied to the cube to…

A: Here in this Question The Edge length of the copper cube is given to be 85.0 cm and it has been…

Q: The beam is supported by a pin at C and an A- 36 steel guy wire AB. If the wire has a diameter of…

A: Solution:-Given thatDiameter of the wire (d)=0.2 inuniformely distributed load (w)=1000 lb per ft

Q: A high-carbon steel wire, circular in cross-section, has a diameter of 14 mm. What is the force (in…

A:

Q: Find the stresses in members BC, BD, and CF for the truss shown in Indicate the tension or…

A:

Q: What is the compressive stress F/A on a woman's feet, in units of kilopascals (kPa) , if the woman's…

A: Given Data: The mass of a woman is, m=52.0 kg The area of each shoe is, A=185.0 cm2   The effective…

Q: Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P…

A: Consider the given data as below. Diameter of wire CD, dw=18 inch Diameter of the pin at B, dp=18…

Q: A cable is 10.0 m long and has a diameter of 2.00 mm. A force of 45.0 N is applied to the end of the…

A: Length of Cable L=10 m Diameter of the cable d=2.00mm=2*10-3m Force applied to the End of the cable…

Q: The bulk modulus of a material is 7.24 x 1011 N/m². What fractional change in volume does a piece of…

A:

Q: A biomechanical model of the bones and biceps muscles of a person's arm supporting a mass m=2 kg is…

A: Stress is a quantity that describes the magnitude of forces that cause deformation. Stress is…

Q: Assuming P=10 kips in the connection shown, determine the maximum bearing stress between the rivet…

A: Given :P =10 kipsrivet measurement : 0.5 inch ( 12 inch )

Q: The beam is supported by a pin at A and a short link BC. Figure 0.5m 1 m 4P 1.5 m 4P 1.5 m 0.5m 1 of…

A:

Q: ó vértical forces are ce ái Determine the ma: BC of the beam.

A: RA + RD =20 kNDue to symmetrical loadingRA = RD =10kNB and C moment is constant and also…

Q: A force is applied to a circular surface with area 70 cm². The surface is parallel to the x-y plane.…

A:

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A: Given:   m= 216kgmg = 216×9.81N      = 2118.96N Solution: The FBD of the member AB is shown below:…

Q: Two people are carrying a 16.3-kg uniform wooden board that is 3.00 m long. One person applies an…

A: Given data: Mass of wooden board, m=16.3 kg Length of the board, L=3.00 m Upward force, F=70.0 N

Q: The bulk modulus of a material is 5.62 × 1011 N/m2. What fractional change in volume does a piece of…

A: bulk modulus of a material is 5.62 × 1011 N/m2. What fractional change in volume does a piece of…

Q: A solid copper cube has an edge length of 80.8 cm. How much stress must be applied to the cube to…

A:

Q: An Aluminum cable of length 3.5 m has 15,000 N tensile force acting on it, if the wire is only…

A: Given, The length of the alumunium cable, L=3.5 m The tensile force acting, F=15000 N Length by…

Q: A wire of circular cross-section, has a tensile force of 60.0 N applied to it and this force…

A: Here, σ=FAA=Fσ=60.0N3.06×106 Pa=19.61×10-6 m2=19.61 mm2

Q: A brass wire is to withstand a tensile force of 350 N without breaking, What minimum diameter must…

A: Given that, Tensile force of brass wire, F = 350 N Tensile strength of brass, E brass = 9.0 x 1010…

Q: A steel wire having a radius of 2.0 mm, carrying a load of 4 kg, is hanging from a ceiling. Given…

A:

Q: A 25-ft crane supported at its lower end by a pin is elevated by a horizontal cable. A 250-lb load…

A: Data:Length of the crane, L = 25 ftDistance of cg, x = 10 ftMass of the load, M = 250 lbMass of the…

Q: A steel rod 55 cm long has a diameter of 30.0 cm.  The compressive strength (the maximum stress it…

A:

Q: What is the maximum length of steel cable that can hang vertically supported from one end of the…

A: A cable hangs vertically supported from one end of the steel cable. And the density of this steel is…

Q: Situation: A simply supported rectangular beam 400 mm wide having an effective depth of 550 mm…

A: Shear force at the face of support is 411 KN. However, for simply supported beam, the location of…

Q: Structural member AB is to be supported by a strut CD. Determine the smallest length CD may have,…

A: Solution: The given diagram is redrawn as given below.

Q: 60. A copper cylinder and a brass cylinder are stacked end to end, as in the drawing. Each cylinder…

A: Given: Cylinder's radii, r=0.25 cm=0.25×10-2 m Force, F=6500 N Copper length, Lcu=3 cm=3×10-2 m…

Q: Problem 2 P A 40 kips 30 in. 30 kips B 30 kips 40 in. Two solid cylindrical rods AB and BC are…

A: We have to find the force P