determine the stiffness k of each spring so that the 30-N force causes the bar to tip angle = 15 degrees when the force is applied. Originally the bar is horizontal and the springs are unstretched. Neglect the weight of the bar. and the springs are unstretched. Neglect the weight of the bar. app

determine the stiffness k of each spring so that the 30-N force causes the bar to tip angle = 15 degrees when the force is applied. Originally the bar is horizontal and the springs are unstretched. Neglect the weight of the bar. and the springs are unstretched. Neglect the weight of the bar. app

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4-47. The support consists of a solid red brass C83400 post surrounded by a 304 stainless steel tube. Before the load is applied the gap between these two parts is 1 mm. Determine the greatest axial load that can be applied to the rigid cap A without causing yielding of any one of the materials. A 0.25 m = 1 mm 60 mm 80 mm Prob. 4-47 -10 mm
please include the FBD
PLEASE SOLVE THIS AS SOON AS POSSIBLE AND SURELY I WILL RATE YOU. THANK YOU ( STEP BY STEP PROCESS)
7) Tabulate the result of your design. In 2 columns, list the tension members on the 1st column and the corresponding angle section on the 2nd column. 8) Write your COMPLETE solution for the analysis and design. P1- 19kN P2- 19kN
4-47. The support consists of a solid red brass C83400 copper post surrounded by a 304 stainless steel tube. Before the load is applied the gap between these two parts is 1 mm. Given the dimensions shown, determine the greatest axial load that can be applied to the rigid cap A without causing yielding of any one of the materials. mm 0.25 m SOLUTION 60 mm -10 mm
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P= 20 KN is applied. Sleel E-200 GPa A-400mm L1 m 2.0 m 0.6 m 1.5m P-20 KN Aluminum E70 GPa A-900mm L-1.5 m 1. Axial load at steel rod in kN? 2. Axial stress at steel rod in MPa? 3. Axial deformation of aluminum rod in mm? 4. Axial deformation of steel rod in mm? 5. Axial Load at aluminum rod in kN?
PLEASE DRAW AND LABEL PROPERLY THE FBD. THANK YOU. From the frame loaded as shown. Solve the following: a. Reaction at column A.b. Moment at column A.c. Force at member GH.d. Force at member FE.e. Force at memeber FH.
How much service live load, in kN/m, can be supported? The member weight is the only dead load. The axial compressive load consists of a service dead load of 45 kN and a service live load of 90 kN. Do not consider moment amplification. Use NSCP 2015. a. b. LRFD. ASD. wt A kN/m mm² W460x144 1.41 18400 472 13.6 283 SECTION tw bf tf Ix Sx mm mm mm mm³ 22.2 726 3080 mm mm mm 199 6.2m W460x144 Sy Ty Zx ly mm mm³ mm 83.6 591 Zy J Cw mmº mm³ mm³ 67.4 3450 906 2440 4230 mmª
IDENTIFY THE ZFM ZERO FORCE MEMBERS
DETERMINE THE FORCE (b) FOR MEMBER AC GIVEN THE DATA BELOW F1-599 tb F-1.283 lb "Note. for comprension, include a negative sign (-)and for tension. type your answer as is input your aniwer in two (2) without the unit F1 30° 60 60° E C A X1 X2 F2 F2
Do not use chat gpt
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P 20 KN is applied. Sheel E200 GPa L-1 m 2.0 m 0.6m 1.5m P-20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the axial load at steel rod in KN?