The support consists of a solid red brass C83400 copper post surrounded by a 304 stainless steel tube. Before the load is applied the gap between these two parts is 1 mm. Given the dimensions shown, determine the greatest axial load that can be applied to the rigid cap A without causing yielding of any one of the materials. 1 mm 0.25 m SOLUTION 60 mm 10 mm

The support consists of a solid red brass C83400 copper post surrounded by a 304 stainless steel tube. Before the load is applied the gap between these two parts is 1 mm. Given the dimensions shown, determine the greatest axial load that can be applied to the rigid cap A without causing yielding of any one of the materials. 1 mm 0.25 m SOLUTION 60 mm 10 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The column above is subjected to axial loading only. Assume the following: • E= 29000 ksi G = 10000 ksi • = 986 in4 A = 60 in? • L= 20 ft • Grade 60 steel (60 ksi yield stress) • The column is fixed at the top and pinned at the bottom Which of the following is closest to the maximum normal stress the column can support (before yielding or buckling)? 167 ksi 24 ksi 42 ksi 60 ksi
What maximum load P can be applied without exceeding an allowable stress of 70 MPa for aluminum or 120 MPa for steel? Can a larger load P be carried if the length of the aluminum rod is changed. the length of the steel portion being kept the same? If so, determine this length
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
A 1 m wide and 3 m long flat plate, held stationary, parallel to the flow direction of a uniform on coming stream of water velocity 3 m/s, leaves a velocity profile, at its trailing edge, varying linearly from zero at the plate to the free stream velocity of 3 m/s at 5 cm away from the plate. The water flow is only on one side of the plate. Assuming the pressure to be the same everywhere in the flowing water, the drag force on the plate will be: 2071
Two T-shape sections are welded together to create a composite l-beam section as shown below. Determine the safely uniform load w (kN/m) that the beam can carry throughout its entire span. 270mm 30mm 20mm 160mm Welded Joint 130mm 30mm 135mm Beam Length = 4 m Consider the following stresses: fb(T) 3 125 МPа fb(C) = 130 MPa x at the welded joint = 20 MPa Find: 1. The Neutral Axis from the base 2. moment of inertia with respect to the horizontal centroidal axis 3. Q at the welded joint 4. Considering the maximum flexural stress in tension, WNAX is equal to KN/m. 5. Considering the maximum flexural stress in compression, WMAX, is equal to 6. Considering the stress at the welded joint, wMex is equal to kN/m.
Round off final ans only, dont round initial values
1
The assembly consists of two red brass C83400 copper rods AB and CD of diameter 30 mm, a stainless 304 steel alloy rod EF of diameter 40 mm, and a rigid cap G. The supports at A, C and F are rigid. Modul of elasticy for the copper is Ecopper = 101 GPa. Modul of elasticity for the steel is Esteel = 193 GPa. (Figure 1) Figure ▼ Part A σAB = Submit Part B Value Submit μÀ Request Answer Part C LO OCD = Value Determine the average normal stress developed in the rod AB. Express your answer to hree significant figures and include the appropriate units. μA Request Answer EF = Units Units A μÃ -300 mm- Value C 30 mm Determine the average normal stress developed in the rod CD. Express your answer to three significant figures and include the appropriate units. Submit Request Answer 30 mm ? B D G ? E 450 mm 40 kN 40 kN 40 mm Determine the average normal stress developed in the rod EF. Express your answer to three significant figures and include the appropriate units. Units F ? < 1 of 1
The axial assembly consists of a solid 1.01-in-diameter aluminum alloy [E = 8900 ksi, v = 0.33,a = 12.4x 10-6/°F] rod (1) and a solid 1.63-in-diameter bronze [E = 15400 ksi, v= 0.17, a = 7.3x 10-6/°F] rod (2). Assume L,=15 in., L2=29 in. If the supports at A and Care rigid and the assembly is stress free at 6°F, determine: (a) the normal stresses o1,02 in both rods at 167°F (positive if tensile, negative if compressive). (b) the displacement ug of flange B (positive if to the right, negative to the left). (c) the change in diameter Ad, of the aluminum rod. B (1) L1 L2 Answers: (a) o = ksi, o2 = ksi (b) ug = in. (c) Adi i in.
The assembly consists of two A992 steel bolts AB and EF and an 6061-T6 aluminum rod CD. When the temperature is 30°C, the gap between the rod and rigid member AE is 0.1 mm. Assume BF is also rigid. (Figure 1) Figure 400 mm A B 25 mm 50 mm D 0.1 mm 300 mm E 1 of 1 25 mm Part A Determine the normal stress developed in the bolts if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. of = Submit Part B σ₁ = Submit O HA Value Request Answer Provide Feedback ■μÅ Value Determine the normal stress developed in the rod if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units Request Answer wwwww Units ? wwwww Review ? Next >
2- The Tensile stress of AISI 1035 Cold-drawn steel is; (a) 550 MPa. (b) 500 MPa. (c) 450 MPa.