Determine the shear, axial, and bending moment distributions for the loaded beam shown below. Write equations for axial and shear forces as well as bending moment as a function of distance along the beam from left to right. Also, sketch graphs of shear and axial forces and bending moments.

Determine the shear, axial, and bending moment distributions for the loaded beam shown below. Write equations for axial and shear forces as well as bending moment as a function of distance along the beam from left to right. Also, sketch graphs of shear and axial forces and bending moments.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam shown, the magnitude of the concentrated load is P = 23 kN, the magnitude of the couple is MB = 350 kN·m, and the beam lengths are a = 7.2 m and b = 21.6 m.(a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A.(b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Part 1 Cut a cross-section through the beam at variable distance x, where 0 < x < a. Derive equations for the shear force V and…
A beam having a tee-shaped cross section is subjected to equal 18 kN-m bending moments, as shown. Assume bf = 125 mm, tf = 25 mm, d = 185 mm, tw = 20 mm. The cross-sectional dimensions of the beam are also shown. Determine the centroid location (measured upward from the bottom), in mm rounded to the nearest tenths. What is the bending moment, shear force, (in kip-ft rounded to the nearest whole number) at x = 9.0 ft? Determine the moment of inertia about the z axis. Express your answer in (106) mm4 rounded to three significant figures Determine the controlling section modulus about the z axis. Express your answer in (103) mm3 rounded to three significant figures
For the beam shown, the magnitude of the concentrated load is P = 28 kN, the magnitude of the couple is MB = 230 kN·m, and the beam lengths are a = 5.8 m and b = 17.4 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Give me all right solutions with clear calculations
Problem: Analyze the continuous beam shown in Figure by drawing the shear and bending moment diagram and sketch the elastic curve. 10 ft AB 1.2 k/ft 30 ft 60 k ↓ 20 ft 10 ft 40 k 15 ft 5 ft E
For the beam shown, the magnitude of the distributed load is wo = 11.8 kN/m and the beam length is L = 8.0 m. (a) derive equations for the shear force Vand the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the maximum shear force and maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Wo A B L Answer: Vmax = kN Mmax = kN-m
Learning Goal: A beam with length L = 2.9 m is supported by a pin joint at A and a cable attached at C as shown in (Figure 1). It is subjected to the distributed load with w₁ =1.7 kN/m and w₂ = 2.1 kN/m. The angle between the cable and the beam is 0 = 35°. Determine the normal force, shear force, and bending moment acting at point B, located x = 0.6 m to the left of the end of the beam. D Wi W2 C B L Begin by finding the support reactions for the beam using the free-body diagram shown in (Figure 2). What is the tension in the cable? Express your answer to three significant figures with appropriate units What is the horizontal reaction force at A? Assume the forces acts in the direction shown, and use an appropriate sign. Express your answer to three significant figures with appropriate units. What is the vertical reaction force at A? Express your answer to three significant figures with appropriate units. Now calculate the internal loading at point B using the free-body diagram of…
For the beam shown, the magnitude of the concentrated load is P = 12 kN, the magnitude of the couple is MB = 150 kN·m, and the beam lengths are a = 4.7 m and b = 14.1 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Solve the intermediate beam shown on the page using the slope deflection matter. Draw the deflected shape, free body diagrams, and the bending movement diagram for the structure with the maximas, minimas, zeros and their locations
Mechanics of deformable bodies. Two decimal places.
Provide completely all answer pls...