1 Determine the shear and moment as a function of , andthen draw the shear and moment diagrams for the beamin (Figure 1).Figure15 kN-m2 kN/m-3 m< 1 of 1▼Part ADetermine the shear as a function of 2.Enter your answer in terms of 2, where z is in meters. Express your answer in kilonewtons.V=SubmitΜΠΙ ΑΣΦ 11 vecRequest Answer3?kN Determine the shear and moment as a function of , andthen draw the shear and moment diagrams for the beamin (Figure 1).Figure15 kN-m2 kN/m3 m-< 1 of 1Part CDetermine the moment as a function of .Enter your answer in terms of , where x is in meters. Express your answer in kilonewton-meteM =SubmitIVE ΑΣΦ ΑRequest Answervec?kN.m

Given data: Udl=2KN/m and moment M=15KN-m act on cantilever beam . To be calculated: Shear and…

Determine the shear and moment as a function of , and then draw the shear and moment diagrams for the beam in (Figure 1). Figure 15 kN-m 2 kN/m -3 m < 1 of 1 A ▼ Part A Determine the shear as a function of 2. Enter your answer in terms of 2, where z is in meters. Express your answer in kilonew V= Submit ΜΠΙ ΑΣΦ 11 vec 3 Request Answer ? kN

Determine the shear and moment as a function of , and then draw the shear and moment diagrams for the beam in (Figure 1). Figure 15 kN-m 2 kN/m -3 m < 1 of 1 A ▼ Part A Determine the shear as a function of 2. Enter your answer in terms of 2, where z is in meters. Express your answer in kilonew V= Submit ΜΠΙ ΑΣΦ 11 vec 3 Request Answer ? kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8 the ban
Question 6 a) The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm³); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm² and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m² per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine. c) Figure Q6c shows a pulley system with a suspended load w of 2000 N. Calculate the following: (i) (ii) (iii) (iv) The effort force (FEffort) necessary to lift and hold a load of 2000 N. The ideal mechanical advantage…
Find the Ixx value for the plate as shown below, where b1=d2=18 mm, d1=85 mm,b2=65mm. (ENTER ONLY THE VALUES IN THE BOXES BY REFERING THE UNITS GIVEN IN THE BRACKET) b1 b2 d2 d1 O The X value (unit in mm) =.
answer this; The numerical value of ? can be calculated as mm
The system shown is in static equilibrium and motionless. Consider the 10 kN force as "the load" on the system. • The coefficient of static friction at a rope/shaft interface is 0.25. • The coefficient of kinetic friction at a rope/shaft interface is 0.16. NOTE: • Submitted responses shall be to 4 significant figures. Do NOT use scientific notation. Find: 8. The angle of wrap around the upper-left shaft is 9. The angle of wrap around the lower-right shaft is 10. The maximum magnitude of the force P that will not initiate upward motion of the load is rad. _kN. 11. The minimum magnitude of the force P that will not initiate downward motion of the load is _kN.
Determine the following: x, y, Ix, Iy 1. y -240 mm 16 mm 12 mm 150 mm -10 mm 12 mm 16 mm 180 mm-
The 10-kg crate is subjected to a force having a constant direction and a magnitude F = 100 N. When s = 15 m, the crate is moving to the right with a speed of 8 m/s. Determine 1) The normal force between the crate and the ground. 2) Its speed when s = 25 m. %3D The coefficient of kinetic friction between the crate and the ground is mk = 0.25.