NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.A commercial refrigerator with refrigerant-134a as the working fluid is used to keep the refrigerated space at -30°C byrejecting its waste heat to cooling water that enters the condenser at 18°C at a rate of 0.28 kg/s and leaves at 26°C. Therefrigerant enters the condenser at 1.2 MPa and 65°C and leaves at 42°C. The inlet state of the compressor is 60 kPa and-34°C and the compressor is estimated to gain a net heat of 420 W from the surroundings. The heat exchanger loses noheat to the environment.26°C↑42°C1(3)ExpansionvalveCondenserEvaporatorQLWater1.2 MPa65°C↑linWinCompressor60 kPa-34°CDetermine the refrigeration load. (Take the required values from saturated refrigerant-134a tables and steam tables.)(You must provide an answer before moving on to the next part.)The refrigeration load is 6.273 ✪ KW.

Answered: Image /qna-images/answer/5c67b98d-e08e-44a5-8cce-bcf2bab74e7d.jpg

Determine the refrigeration load. (Take the required values from saturated refrigerant-134a tables and steam tables.) (You must provide an answer before moving on to the next part.) The refrigeration load is 6.273 kW.

Determine the refrigeration load. (Take the required values from saturated refrigerant-134a tables and steam tables.) (You must provide an answer before moving on to the next part.) The refrigeration load is 6.273 kW.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5.18 : Taking the data of the preceding problem except the final temperature of the cooling water is to be taken to apply to a jet condenser, calculate the weight of injection (cooling) water required per kg of steam.
Explain the placement for these item in the system: - Steam turbine - Gas turbine - Heat pump
I think its Chemisty... If an evaporator outlet temperature on an R-410A system is 50f and the evaporator superheat is 10f, what is the evaporating pressure of the refrigerant in the system?
Required information Refrigerant-134a enters the condenser of a steady-flow Carnot refrigerator as a saturated vapor at 65.0 psia, and it leaves with a quality of 0.05. The heat absorption from the refrigerated space takes place at a pressure of 30 psia. Determine the coefficient of performance. (Round the final answer to three decimal places.) The coefficient of performance is
Every closed feedwater heater generates a condensate. Determine:a) If it is sent to the high pressure line, what device (or machinethermal) is required to be used for this purpose.b) It would be required to install a mixing chamber. Why or for what?
1. A standard vapor compression refrigeration system uses Ammonia as refrigerant. The Ammonia leaves the evaporator at – 20 degree Centigrade and the condenser pressure is 1200 kPa. The flow rate is 30 kg/min. Determine a) the tons of refrigeration b) the power required c) the COP.
A refrigeration system using refrigerant 12 is to have a refrigerating capacity of 80 kW. The cycle is a standard vapor-compression cycle in which the evaporating temperature is -15°C and the condensing temperature 30°C. At the entrance to the evaporator, what is the fraction of vapor in the mixture expressed on a mass basis? 0.97 0.29 0.92 0.27
The values of a vapor compression refrigeration cycle were given below. Calculate the values ofrefrigerant flow rate, refrigeration capacity, and the COP of the system.T1= Evaporator water outlet = 10 °CT2= Evaporator water inlet = 16 °CT3= Condenser water inlet = 16 °CT4= Condenser water outlet = 22°CCooling water flow rate = 1.5 L/minHeating water flow rate = 1.5 L/minEnthalpy of R134a in evaporator outlet = 305 kj/kg,Enthalpy of R134a in evaporator inlet =115 kj/kgEnthalpy of R134a in condenser inlet =327 kj/kg
Question 2 of 4 - / 25 An office building requires a heat transfer rate of 30 kW to maintain theinsidetemperature at 21°Cwhen theoutsidetemperature is O°C. Avapor-compression heat pump with Refrigerant 134a astheworkingfluid isto beused to provide the necessary heating. The compressoroperates adiabatically with an isentropic efficiency of 82%. Determine appropriate evaporator and condenser pressures of a cyclefor this purpose assuming ATcond = ATevap = 10°C, as shown in the T-sdiagram. The refrigerantexitstheevaporator assaturated vapor and exitsthecondenser as saturated liquid at the respective pressures. AT cond Outside air 21°C 0°C Inside air ATent Condenser Evaporator Expansion valve Compressor Step 1 Determinethe mass flow rate of refrigerant, in kg/s. m = kg/s Attempts: unlimited Submit Answer Save for Later Using multiple attempts will impact your score. 5% score reduction after attempt 2 Step 2 The partsof thisquestion must becompleted in order. This partwill be availablewhen…
can you please solve this for me (the fraction of steam extracted from theturbine for the open feedwater heater)
iii) the exit area of the nozzle. Take Cp = 1.005 kJ/kg-K and R=287 J/kg-K Q.B3. A heat engine operates between two reservoirs at 400°C and 30°C. Half the power produced by the heat engine is used to drive a Carnot heat pump that removes heat from the cold surroundings at 2°C and transfers it to a house maintained at 27°C. The heat engine is absorbing heat at a rate of 5 kJ/s. i) Draw the complete schematic of the device ii) Determine the thermal efficiency of the heat engine iii) Determine the coefficient of performance of the heat pump iv) Determine the rate of heat loss from the house. v) Determine the minimum rate of heat extraction by the heat pump, and vi) the total rate of heat rejection.
In actual design, as per illustration Fig. MT 1, the system has a liquid reservoir also acting as an accumulator. The line that connects to the thermal expansion valve is connected underneath the accumulator. This will ensure that only ___ refrigerant will be atomized by the value supplied to the evaporator. SUBJECT: REFRIGERATION SYSTEMS