Determine the reaction at the supports and the reaction at point D. El is constant

Q: determine the value of the reactions  RA= RFY/RFX=

A:

Q: B 0.6 m 45 KN 1.8 m 73 kN/m A

A:

Q: Determine the reaction at A (kN).

A: Given Weight = 843 kN To find Reaction at A

Q: 6) Find the horizontal and vertical components of the reactions at points A and D. 2m D -1.5 m B 1.5…

A: Given

Q: For the following calculate the reactions at A and B. 2 kN-m 6 kN-m A 60° 2 m

A:

Q: Determine the resultant reaction at A

A:

Q: Determine the reaction At C

A:

Q: Determine the reactions at the point .(A) and (B) 5KN 2.4M 1-2 m 1.2m 1.2m

A: For the given simply supported beam  To determine  reaction at point A and B

Q: Determine the reactions at the supports. 350 N/m 150 N/m 80 N/m 3.5 m 4.5 m

A: Given: To determine the support reactions. The load will be divided as uniformly distributed load…

Q: Determine, using the principle of superposition, the reactions at supports A and B for equilibrium.…

A: Given: The load intensity, w = 300 N/m

Q: The cylinder have equal diameter. Solve for the reactions at A, D and C.

A: Given Cylinder weight 20 kN 40 kN 30 kN To find Reaction at A, D and C

Q: Situation 4: Determine the support reaction at A? * 390 lb 1312 800 lb - ft 8 ft -4 ft- 3 ft 30% B

A:

Q: Principle of superposition to determine the reactions at the supports A and B.EI is constant

A:

Q: 3m O 2078 N 1800 N 800 N/m 30° 3 m B

A:

Q: Determine the reactions at A and E if P = 920 N. The reactions are positive if to the right or up,…

A:

Q: 625 N /m 400 N /m A B 2.5 m 6 m

A: Given Data The uniform distributed load acting on the beam is 400 N/m.  The uniform varying load…

Q: Determine the reaction at A on the beam. Let wo = 97 kN/m, L= 3 m.

A:

Q: 150 mm 100 mm 200 mm, Two transmission belts pass over a double-sheaved pulley that is attached to…

A: The radius of inner sheave, r = 145 mmThe radius of outer sheave, R = 213 mmThe tension at both…

Q: The extended beam ABC in the figure below is pin-supported at A and roller-supported at B. For the…

A:

Q: Find the magnitude of the reaction at point C

A: given - figure  to be find-magnitude of the reaction at point C

Q: Problems: Determine the reaction -4 in.- 4 in. 40 lb 20 lb 2 in. CO 3 in. 3 in. 30%

A:

Q: find the reaction at A,C

A: To find :- Reaction

Q: The moment reaction at B is

A:

Q: Determine the reactions at points A and B, and find the internal forces at point C. 200 N/m A 3 m

A:

Q: For the structure loaded as shown in the figure, determine the reaction at A

A:

Q: 0.1414K/&+ 0.5 A

A: Draw the free-body diagram of member AB.

Q: Use the Principle of superposition to determine the reactions at the supports A and B. El is…

A:

Q: Solve for the component of the reactions.

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.