Determine the power transmitted through the shaft of a car when the torque applied is 200 N – m and the shaft rotates at a rate of 420 radians per second. O a. None of the mentioned O b. 121.9 hp O c. 110.4 hp 112. 0 bn

Q: Q1: A rotating shaft carries four masses A, B, C, and D radially attached to it. The centers of mass…

A:

Q: The shaft ABCDE is under equilibrium. Determine the internal torque in section (3). 39.00 N-m 37.00…

A:

Q: HW 1// For the thin walled shaft shown below, find the angle of rotation of one end with respect to…

A:

Q: FD Fc FB F.

A: Four forces, FA, FB, FC, and FD, each of magnitude 1 N, are applied to a square object at the points…

Q: Member ABCD is a hollow circular steel shaft with a 4 inch outer diameter and a 3 inch inner…

A: Given data:- a hollow circular steel shaft outer diameter =4 inch inner diameter =3 inch  TB…

Q: 4. In radial bearings, the load acts O(A) Along the axis of rotation O(B) Perpendicular to the axis…

A: Given: Radial bearing

Q: Find the displacement of object to be done so that work done is 433 J if force applied 22 N

A: Given data : Work done W=433 J Force applied F=22 N   Required : Displacement

Q: -5 ft- – 1ft -6 ft GB B 70° M G. 20 250 Ib 3 ft 2.5 ft

A: by using the moment formula force * perpendicular length will get moment is   Moment 301 lf.ft

Q: The car engine has a torque of 0.4 kNm at 2000 rpm (rev/min). What is the power (kW) at this time?

A: Given data: torque (T) = 0.4 kNm Speed (N) = 2000 rpm Need to determine the power.

Q: The potential energy of a spring is a. Always negative b. Always positive c. Positive or negative…

A: This question is based on the concept of potential energy of spring.

Q: The torque of a steel shaft transmitting 20 kW at 320 rpm is

A: Power transmitted by the steel shaft, P = 20 kW = 20*103 W Revolutions, N = 320 rpm

Q: Resolve and draw the diagram of all internal efforts

A: For the above diagram, We draw a free body diagram,

Q: QUESTION 5 Determine the power transmission through the shaft of a car when the torque applied is…

A:

Q: Torque to weight ratio for a circular shaft

A: Given; Torque to weight ratio for a circular shaft transmitting power  is directly proportional to…

Q: ) Indicate the direction of all force components of worm and worm ear. 斗 2.

A:

Q: RSL-2 A rod of negligible mass is pulled down at each end as shown to the right. The rod is…

A:

Q: The polar moment of inertia of the segment AB is

A: Given: d3 =77 mm =0.077 m To determine the polar moment of inertia of the segment AB

Q: Two shafts, having axes in the same plane intersecting at an angle of 45 degrees, turn in opposite…

A:

Q: What is θ3

A: Given, AD=10 cmAB=4 cmBC=7 cmCD=6 cmθ2=900

Q: 1. Determine the cylinder displacement and engine displacement of an engine having six cylinders…

A: given data  bore diameter = 102 mm = 0.102m stroke length  = 120mm =0.120m number of cylinders =6…

Q: Q2: Detrmine the maximum Torque (T) that can be applied without exceed the shearing stressess and…

A:

Q: Find the displacement of object to be done so that work done is 433 J if force applied 22 N

A:

Q: 1. Four pulleys are attached to the 55 mm diameter steel shaft. If torques is applied to the pulleys…

A: Given data: The diameter of the shaft, d=55 mm. Refer to the table "properties of steel: to the…

Q: A device is powered by a geared motor which produces a torque of 80 N-cm. The work done by the…

A: Given: Word done, W = 160 N-mm Torque, ? = 80 N-cm = 800 N-mm Angle, θ = ?

Q: 1. Disk 2. Disk 2000 грm 212 212 a =b =c = 300 mm 30 e12 30 l = 200 mm A

A: Given : Solution : The angular velocity is given as:

Q: e of rotation of end A of the gear-and-shaft system? unit of Degree)

A:

Q: A) Resolve the 500-lb of fig. into two components: a shearing component parallel to AB and a normal…

A:

Q: The outside diameter of a hollow shat is 1.6 times the inside diameter. When transmitting 420 W of…

A:

Q: A CIRCULAR STEEL SHAFT (G= 80 G Pa ) Is COADED Bu Two TORQUES. AT Points A Awo C As SHOWN. FiNo: THE…

A: Given data, G= Modulus of elasticity of the shaft=80GPa =80x103 MPa T = Torque applied =1000x103 Nmm…

Q: A shaft transmits (7.5 x ) kW of power at a speed of 150 rev/min. The torque on the shaft is: O a.…

A:

Q: T 100 mm 70 mm 70 mm 1.5 m 2 m T

A:

Q: A loading condition is shown below. Using Castigliano's theorem and by applying a fictitious force Q…

A: (a) The free-body diagram of the beam BD is given as, Now, apply force equilibrium in a horizontal…

Q: For an object of spherical shape, the value o critical radius would be

A: Given: Spherical shape

Q: Calculate the forces at a: F_Ax = ___________, F_Ay=__________________, and the forces at D: F_Dx =…

A:

Q: tage of 2,5:1 acts on the master cylinder which is 15 mm in diameter. Hydraulic  fluid is displaced…

A: Dm=15mmDs=20mm Fs=850NP=70mm To-Find:- 1) The force which must be applied to the foot pedal2) The…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.