Determine the power loss and coefficient of friction for a hydrodynamically - lubricated full - film, bronze, short bearing of l/d = 0.75 that supports a 150-mm- diameter shaft carrying a load of 15 kN at a speed of 60 rpm. The clearance ratio is 0.002 and the Ocvirk number is 40. Answer: Tr = 4.56 Nm; power loss = 28.65 W; coeff of friction = 0.004

Determine the power loss and coefficient of friction for a hydrodynamically - lubricated full - film, bronze, short bearing of l/d = 0.75 that supports a 150-mm- diameter shaft carrying a load of 15 kN at a speed of 60 rpm. The clearance ratio is 0.002 and the Ocvirk number is 40. Answer: Tr = 4.56 Nm; power loss = 28.65 W; coeff of friction = 0.004

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You are asked to design a four cylinder four-stroke compression ignition engine for light trucks, which is required to provide a maximum brake torque of (2.000x10^2) Nm at the rated speed of (4.50x10^3) rpm. The bore (B)/stroke (L) ratio is required to be (9.0000x10^-1). Given that the bmep of the engine is assumed to be (1.0000x10^3) KPa, find its stroke (L). The answer should be in the unit of meter with 3 significant figures.
hand written solution plzzz
solve part (iv)
A flat belt with a width of 120 mm and a thickness of 5 mm transmits power from a driving pulley with a diameter of 250 mm to a driven pulley with a diameter of 700 mm. The mass per unit length of the belt is 2.1 kg/m, and the coefficient of friction is 0.25. The input power of the belt is 60 kW at 1000 rpm. Calculate the following when the center distance is 3.5 m. (a) Maximum tensile stress of the belt(b) Axial load on each pulley
A double-thread trapezoidal-metric-thread-form screw, which is driven by a motor, raises a nut and the attached load of 16 KN at a speed rate of 12 m/min. The screw has a pitch of 6mm and a mean diameter of 38 mm. The collar (with worn-out surface) has diameters of D = 70mm and d = 40mm. The coefficients of thread and collar friction are both 0.1. Determine the power in kW required to raise the load. Round your answer to 4 significant figures.
Design a single row deep groove ball bearing with basic dynamic load rating of 25.5 KN to be used in a turbine to carry a radial load of 1607 N. The expected life of the bearing is 5226 hours at 523 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.8. The radial and axial load factors are 1.3 and 1.6 respectively and the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Axial load acting on the bearing in N
A pressure-fed bearing has a journal diameter of 63.00 mm with a unilateral tolerance of -0.05 mm. The bushing bore diameter is 63 084 mm with a unilateral tolerance of 0.010 mm. The length of the bushıng is 58.00 mm. Its central annular groove is 8.00 mm wide and is fed by SAE 30 oil is 55°C at 195 kPa supply gauge presaure. The journal speed is 2880 revimin carrying a load of 20 kN. The sump can dissipate 300 watts per bearing if necessary. For minimum radial clearances, find the average temperature Given the film temperature is 95°C
i need the answer quickly
A Self-aligning medium series bearing for bores of 85 mm is operating at 300 r.p.m for an average life of 9 years at 10 hours per day, is acted by a 15 kN radial load and 10 kN thrust load. The bearing is subjected to a light shock load and the inner ring is sationary. Determine the suitable self-aligning bearing. Mention the advantage of using self align bearing.
The shaft below is supported by 0.5 in long copper-iron light-duty journal bearings at A and B. Determine the maximum allowable shaft speed (in rpm) consistent with a bearing factor of safety of 1.8. F = 225 lbf Bearing A Bearing B 1.1 in Walow = ? 5.75 in 0.5 in 1.5 in 0.5 in
E1. A full journal bearing has the following specifications: Journal Diameter:46 mm Bearing length: 66 mm Radial clearance to radius ratio: 0.0015 speed : 2800 r/min Radial load: 820 N. Viscosity of the lubricant at the operating temperature:8.4 cP Considering the bearing as a lightly loaded bearing, Determine (a) the friction torque (b) Coefficient of friction under given operating conditions and (c) power loss in the bearing.