what is the right anwer and solution for the total distance? The motion of a particle is defined by the relation x= 3 – 62 + 9t+ 7, where x and tare expressed in feet and seconds, respectively. Determine the position, acceleration, and total distance traveled when t = 5 s.The position is27 ft.The acceleration is18 ft/s2.The total distance is22 ft.

Answered: Image /qna-images/answer/e6d76754-1512-40d8-8b0a-666000ad2da8.jpg

Answered: Determine the position, acceleration,…

Determine the position, acceleration, and total distance traveled when t = 5 s. The position is 27 ft. The acceleration is 18 ft/s2. The total distance is 22 ft.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.19P: Plot the earths gravitational acceleration g(m/s2) against the height h (km) above the surface of...

See similar textbooks

Related questions

Q: The drilling time (in minute) is

A: Given, Diameter,d= 20 mmThickness,t= 40 mm N= 400 rpmFeed rate,f= 0.1 mm/revDetermine the drilling…

Q: Two (2) beams are subjected to different loading condition and position as shown. w1 w2 P x1 x3 w1…

Q: 7.30 5.90 4.50 Stress Lev 3.10 1.70 pox ഇന്നും 00 O 00 DO O XXOOD O OD 0 DOO 0 0 0 Оф COX0000000…

A: The intercept is calculated as the value of stress level at zero percentage From the given figure it…

Q: #1] Given a gear of 16 teeth, 4 diametral pitch. The dedendum equals 1/P, inch, the clearance is to…

A: As per the guidelines of bartelby, a question involving more than three subpart can be solved for…

Q: Determine the range

A: Given data: The magnitude of vertical weight, W = 1200 N. Coefficient of static friction, µs = 0.30…

Q: Water is the working fluid in a regenerative Rankine cycle with one open feedwater heater. Steam…

Q: FAND e Canrid 35 300 SECTION MODULUS , Sx, S O radius of giyntion, rx RuF DMEHSIONS '.RE IN MM. I O…

A: As per guidelines one need to solve only first 3 subparts

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: instantaneous discharge velocity

A: Given; Large tank with a nozzle attached contains three immiscible, inviscid fluids as…

Q: The tape shown slides around two fixed pegs each of radius 30 mm as shown. If T1 = (0.1P in newton)…

Q: 1. Determine the internal normal force, shear force, and bending moment at point c in the beam. 5…

Q: For the quick-return mechanism shown below, the rod DC rotates with a constant angular velocity of 1…

A: For the solution refer below images.

Q: Determine the force developed in members BC and CH of the roof truss and state if the members are in…

Q: The principal stresses of the state of stress.

A: Given:- Principle stress question with solution, To find:- To clear the doubt how -53.13, 26.6, and…

Q: The LiBr-water absorption cycle shown in Fig. 17-2 operates at the following temperatures:…

A: Find the concentration of Li-Br in the generator Tg=100°C Tc=55°C Te=10°C Ta=30°C

Q: Ex] A double-threaded right-handed worm gear transmits 15 Hp at 1150 rpm. The pitch of the worm is…

Q: Determine the reactions at the supports. 5 kN/m 12 kN Figure 1 4 m 2m 2 m

Q: 5. Combustion gases with k=1.35, Cp=1107 J/(kg.K) and R= 287 J/(kg.K) flow at stagnation pressure…

A: Given Data: k = 1.35Cp=1107 J/kg-KR=287 J/kg-Kps=390 kPaTs=1150 Kpstatic=100 kPaM=1ηts=80% To…

Q: 3. Determine the internal normal force, shear force, and bending moment at point C in the beam. 300…

Q: What is the v-velocity at the centerline after refining the mesh

A: To explain: What is the v-velocity at the centerline after refining the mesh.

Q: 2. You are working for a glider manufacturer and have been asked to analyse the laminar boundary…

A: For the solution refer below images.

Q: The answers should not be in vector form. Please re-anser. Rate will be given

Q: 11.51 - BIO Supporting a Broken Leg. A therapist tells a 74-kg patient with a broken leg that he…

A: Given data: M=74 kgm=5.5 kgcenter of mass of each thigh(Tcm)=18 cmcenter of mass of body weight…

Q: Determine the components of the resultant force and the magnitude of the resultant.

Q: A bar ACB has is subjected to an external load at C, and it is supported either end by a cable as…

A: Given:σb=90 MPaσs=120 MPa

Q: 4. Steam turbine with 80% stage efficiency receives steam at 7MPA and 550 deg C and exhausts as…

A: Find the quality after turbine expansion.

Q: Within a unit cubic cell sketch the following slipping direction using Miller indices: 1. [I 1 0] 2.…

A: Given Miller Indices for Directions:- To Do :- Draw the Direction

Q: What is the rate of refrigeration in kW of an ideal heat-operated refrigeration cycle that receives…

Q: Water contained in a piston-cylinder assembly, initially at 300°F, a quality of 60%, and a volume of…

A: Given:Temperature of water, T=300°FQuality of water, x=60%Volume, V=6 ft3Rate of heat transfer,…

Q: for 2 can you please do a sketech veriation of it?

A: Given data :-actual stress and engineered stress with strain To draw :-actual stress and engineered…

Q: A refrigeration system using refrigerant 11 is to have a refrigerating capacity of 80 kW. The cycle…

A: Given Data Refrigerant R-11 Te= -15°C Tc=30°C

Q: A piston-cylinder assembly contains 2 lb of water, initially at 100 lbf/in.2 and 350°F. The water…

Q: 9-67. Determine the principal stress, the maximum in-plane shear stress, and average normal stress.…

Q: 3. A wooden body with relative density of 0.57 floats a liquid with unknown relative density. If the…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: (a) The rotating elements in machine system often generate unbalance forces due to unbalance mass…

Question

what is the right anwer and solution for the total distance?

The motion of a particle is defined by the relation x= 3 – 62 + 9t+ 7, where x and tare expressed in feet and seconds, respectively.

Determine the position, acceleration, and total distance traveled when t = 5 s.
The position is
27 ft.
The acceleration is
18 ft/s2.
The total distance is
22 ft.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Each of four particles move along the x-axis. Their positions (in meters) as functions of time (in seconds) are given as follows: Particle 1: (t) = 3.5 - 2.7³ Particle 2: (t) = 3.5+ 2.7+³ Particle 3: x (t) = 3.5 - 2.7² Particle 4: x (t) = 3.5-3.4t - 2.7t² Which of these particles have constant acceleration? O Only 1 and 2 Only 3 and 4 None of them Only 2 and 3 O All of them
I need help with this question please. thank you
The velocity of A is 1.7 m/s downward, the velocity of B is 2.6 m/s upward, and the velocity of D is 3.1 m/s downward. Find the velocity of C. The velocity of C is positive if downward, negative if upward. D B Answer: vc= i C ! m/s
The displacement of a particle is given by s=3t3-57t² + 114t 44 where s is in feet and it is in seconds. Plot the displacement, velocity. and acceleration as functions of time for the first 18 seconds of motion. After you have made the plots, answer the questions. Questions: Att 4.5 sec. Att 9 sec, Att 14.3 sec, A34 The velocity is zero when t 1 ft.v= ft. v ft, v= === sec and when t= !!! ft/sec, a= ft/sec. a ft/sec. a ft/sec ft/sec ft/sec
The graph represents the straight line motion of a car. How far does the car travel between t = 2 seconds and t = 5 seconds? v(mk) 12 4 m 12 m 24 m 36 m 60 m
thanks
A bullet weighing 0.3 N and moving at 600 m/sec penetrates 40 N body shown in Figure and emerges with a velocity of 180 m/sec. How far and how long will the block move, if = 0.2 between floor and body. 600 m/sec. 180 m/sec 40N ANS: S= m, t = s (ONE DECIMAL PLACE)
Newton's Third Law states that: The velocity of a particle is proportional to the vector sum of forces acting on it, and is in the direction of this vector sum. The acceleration of a particle is proportional to the vector sum of forces acting on it, and is in the direction of this vector sum. The forces of action and reaction between interacting bodies are equal in magnitude, opposite in direction, and collinear. O A particle remains at rest or continues to move with a uniform velocity if there is no unbalanced force acting on it. 7
During a manufacturing process, a component moves in a linear pathsuch that its displacement “s” in mm is described as a function of time “t” inseconds by the equation: s = 3t3- t2 + 5t + 2 (mm) If a time of 1.5 seconds has elapsed in the process, determine :(i) the velocity of the component;(ii) the acceleration of the component.
The diagram below represents a swimmer. The swimmer is capable to swim in a still water with a velocity Vị = 1 m's. He aims his body directly across a 100 m wide river whose current has a velocity V;=2 m/s. Use this diagram to answer questions 1 through 3. 1. The time it will take for the swimmer to cross the river is .. (A) 10 sec (B) 20 sec (C) 50 sec (D) 100 sec 2. How far downstream will he land? The correct answer is (A) 100 m (B) 200 m (C) 150 m (D) 180 m
1- A particle moves along the x axis. Its position varies with time according to the expression x=-41+ 2f where x is in meters and t is in seconds. The position-time graph for this motion is shown in Figure. Note that the particle moves in the negative x direction for the first second of motion, is momentarily at rest at the moment 1 = 1 s, and moves in the positive x direction at times /> 1 s. (A) Determine the displacement of the particle in the time intervals t=0 to 1=1 s and t= 1 s to / = 3 s. B) Calculate the average velocity during these two-time intervals C) determine the instantaneous velocity and instantaneous speed at t= 0.5 s. x(m) Slope = 4 m/s 10 00 8 9 10 O Slope =-2 m/s 1 2 015 t(s)
3. How to solve E, G, and H?