The theoretical value for the standard molar enthalpy of combustion formagnesium is -601.6 kJ/mol. Determine the percent error for your laboratoryinvestigation. Data TableMg (s)MgO (s)Initial Temperature of HCI (aq)("C)Final Temperature of solution("C)Change in temperature("C)23.023.034.838.011.815.0Mass of substance0.130.97(g)Concentration of HCI (aq) = 1.00mol/LVolume of HCI (ag) used in each trial = 0.050L

m=0.13g C= 4.184 J/g°C ∆T=34.8 - 23=11.8°C Heat q= mc∆T =0.13*4.184*11.8=6.41J…

Answered: Determine the percent error for your…

Science

Chemistry

Determine the percent error for your laboratory

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

List which piece of lab equipment would be most useful for each of the following tasks. 1. Hold 50 mL of boiling water. 2. Crush a chunk of chemical into a powder. 3. Heat a beaker of water when a gas line is not available to power any equipment. 4. Measure exactly 42.5 mL of water. 5. Scoop ammonium nitrate out of its container and onto weigh paper to be measured.
Two liquids, A and B are immicible. Liquid A has a density of 0.89 g/mL. Liquid B has a density of 1.00 g/mL. What would you expect to see if you added equal amounts of both liquids to a test tube, shook, and let settle? a. one clear layer b. one cloudy layer c. two layers with A on top d. two layers with B on top
what are the numbers in scientific notation? where did they come from? Is there any chance you could elbaborate on step 2?! Thank you!
Based on the information given, identify the most significant error in the preparation of Graph 2. A) The title appears in a font which is too small. B) The best-fit line does not intersect any data point. C) There is wasted space on the graph. D) The x-axis scale divisions are uneven.
If you have multiple analytical balances to use during a lab, why do you think it is important to use the same analytical balance for repeated weighing?
Question 1 of 30 Convert 0.386 to milligrams . Use only the metric system. 386 mg ADD FACTOR DELETE ANSWER RESET
Here is my current numbers from my chem lab today. I’m not sure how to take these numbers and get the last two calculations. We are supposed to use our lab numbers to get those numbers.
Use the data set below to answer the following question. This is a fictitious data set, so no units are listed. Data Set 282 294 270 276 232 295 For the data set above, the Q-test suspect value is type your answer. and based on the statistics you can choose your answer. that value with 90% confidence.
I need answer for that question you can give the question because it's laboratory experience of chemistry
Laboratory 2 Report Sheet-Lab 2 A.2 Area Your measurements Length = Width = Area = (Show calculations.) Why could two students obtain different values for the calculated areas of the same rectangle? A.3 Volume of a solid by direct measurement Shape of solid Formula for volume of solid 18 Height Width Another student's measurements Volume of the solid (Show calculations of volume including the units.) Length Diameter (if cylinder) Page 3 of 3 482 words 区

Why does the water go up to the bottle? I need claim, evidence and reasoning
Calculate the percent error when a known value of 5.69 is measured to be 5.85