Determine the output of the D/A converter Rf =25

Q: Cyclo Convertors:AC to AC conversion by using Thyristors draw the Circuit diagram and point out the…

A: Cyclo Convertors AC to AC conversion: The circuit diagram is given as:

Q: The input voltage of a Boost converter is 10V, the duty cycle of the boost converter is 0.25. What…

A: Brief description: For the above given question we need to calculate the value of output voltage of…

Q: Calibrated attenuators are used in digital multimeters to the signal level O a. Increase O b.…

A:

Q: B. Square wave input 1. Set R = 470 Q (for the circuit in Figure 5 -3 (a) or R = 22 k2 (for the…

A: A. Given: Set R=470ΩNow, we will calculate α, ω0 and ωdα=R2Lα=4702×100×10-3α=47002α=2350

Q: Multiplexers and statistical multiplexers may be differentiated by

A:

Q: In a DIA converter, LSB represents 0.2 V. The digital input is (0111) will cause an analog output of…

A:

Q: O a. B-a

A:

Q: A boost converter with an input voltage of 5 V dc and an output voltage of 8 V dc will have a duty…

A: Given a boost converter with, Input voltage, Vs=5 V Output voltage, Vo=8 V Duty cycle, α=?

Q: For the given circuit, what is the minimum peak value of the output waveform if the input waveform…

A: Negative Clamper Circuit: A Negative Clamper circuit is one that moves the output signal to the…

Q: The oscillation frequency for the oscillator below is 3.12 MHZ for c=150 PF, L1=L2= 2.2 mH and M=0.5…

A:

Q: e pinch-off voltage of an n-channel JFET is about

A:

Q: The input voltage of a Boost converter is 10V, the duty cycle of the boost converter is 0.25. What…

A: Given: Boost converter, Input voltage, Vin=10 V Duty cycle, d=0.25

Q: A boost converter is supplied from a 110 V DC source. The output voltage required at the load is 220…

A: Given a boost converter with, Supplied or input voltage, Vin=110 V. Required output voltage at the…

Q: Which one of the following is the correct implementation of this multiplexer?

A:

Q: The most common standard electronic current transmission signals range fron to mA.

A: The most common standard signal for electronic transmission is 4 to 20 mA.

Q: etermine the output waveform for the circuit of Figure +10 V Vin OV R ww 1.0 ΚΩ Vou

A: Given data, Circuit diagram is given as,

Q: what are the apllications of DC-TO-DC converter

A: Dc to Dc converter also known as chopper are of three types, namely Step up chopper Step down…

Q: choose the correct answer 4-If the voltage generator is 5 mV in an emitter follower, the output…

A: Input voltage of emitter follower circuit is given, Vin=5 mV

Q: For the common emitter class A power Amplifier shown next figure, answer the following questions: a)…

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: In re The process of comparison of an instrument with absolute instrument is called

A: The solution is given below  The process of comparison of an instrument with absolute instrument is…

Q: In mode of operation, fully controlled converter will keep a delay angle range between 90° to 180°.

A: In this question, we have to find out in which mode fully controlled converter will keep a delay…

Q: Design asynchronuus counter Mod 14

A: Given, To design a 14 mode asynchronous counter

Q: Vin Cy Vcc = 12 V RC 3.3 K RB 270 K Please determine the AC voltage gain. Cx 1.5 K RE Vout Cy beta =…

A: In this question we need to find the AC voltage gain

Q: When used as a power amplifier with a sinusoidal input, the output of an emitter follower is…

A: In the given questions we need to discuss about that when we used  power amplifier with a sinusoidal…

Q: The output voltage of a quadrupler is 220 V. What is the secondary voltage Vm? 55 V   165 V   110…

A: It is given that: Quadrupler output voltage is, Vo=220 V

Q: The frequency of oscillation of the oscillator shown in below figure is C₁ = 10pF HE + L=5µH vooro…

A: We need to find out the frequency of oscillation for given circuit.

Q: Re Cout Cin 王。 Qr Re Build an oscillator with fo = 30MHZ Using Using Q = 2N2222 %3D

A:

Q: A signal is passed through a LPF with cut-off frequency 10 kHz. The minimum sampling frequency is…

A: if Fm is the maximum frequency in the signal , then minimum sampling frequency is 2Fm  .  and cutoff…

Q: C1 3 Vi Vi 2, 20 V 1.0uF Vo R2 1.2k2 Si LV1 =4 V -20 V

A:

Q: Draw the output waveform for the comparator circuit in figure below. Assume that Q? +Vout(max) = +10…

A: The answer as given below:

Q: Determine the period and frequency of oscillation for an astable multivibrator with component values…

A: The astable multivibrator generate square wave. It doesn't require any external triggering pulse.…

Q: 70 50 30 -30 -50 -70

A: We need to find modulation index for given modulated waveform

Q: What is the output frequency of a cascade counter with three stages [MOD-15, MOD-12, and MOD-8] if…

A: Here it is asked to find the output frequency of the cascaded counter. When counters are cascaded…

Q: What will be the output voltage during the negative half cycle of the input voltage? V-SV 20 -10

A:

Q: 2- For the following circuit, draw the output signal. 5.3-4=1.3 Vout 10KQ 6v Vin D2 1N4148 D1 1N4148…

A:

Q: 11. Determine the condition of the SCR in the following conditions: activated or not-activated.…

A:

Q: In 3 phase half wave converter the thyristor T1 is reverse biased due to the 'b' phase supply.…

A: Choose the given statement is it true or false?   In 3 phase half wave converter thr thyristor T1 is…

Q: Find the voltage transfer ratio when another voltage divider of the same type is connected to the…

A: We are given a circuit with a combination of two same voltage divider circuit. Given that:…

Q: In a 10C400 CT, the maximum error occurs at what secondary current? O A. The answwer is not given…

A: In this question We need to choose the correct option What is maximum error  in secondary side.