Determine the open loop transfer function G(s) = C(s)P(s), and identify the open-loop poles and open-loop zeros of the system. (i) (ii) For the root locus of G(s), determine the number of asymptotes and where they meet, and calculate the location of any double point(s). ** (iii) Sketch the root-locus for this system, using the information derived in (i)-(ii) and comment on the characteristics of this system for different values of K, e.g. for small K and for larger values of K.

Determine the open loop transfer function G(s) = C(s)P(s), and identify the open-loop poles and open-loop zeros of the system. (i) (ii) For the root locus of G(s), determine the number of asymptotes and where they meet, and calculate the location of any double point(s). ** (iii) Sketch the root-locus for this system, using the information derived in (i)-(ii) and comment on the characteristics of this system for different values of K, e.g. for small K and for larger values of K.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. i. A Transfer Function of a system is as shown below. (s+3)(s-4) Y(s) (s-5)(s+ 1)(s + 2) Plot the poles and the zeros for this transfer function in an S-plane. Also, indicate the stability of the system. iL. With the help of block diagrams indicate the basic difference between Positive Feedback and Negative Feedback Closed-Loop Control Systems.
For a unity feedback system having K (s2 + 6s + 8) G(s) = %3D s2 + 4s + 13 a) Determine the asymptotes. b) Draw the root locus. c) Find the gain at the point (-3+tj0).
Q.4. Consider a unity feedback control system with feed forward :transfer function is .Q.4 G(s) 12(s+2.5) s (s² + 5s +11) A) It is desired to make the damping ratio (5) of the dominant closed-loop poles equal to (0.5) and to increase the undamped natural frequency (w) to (5 rad/sec) and the static velocity error constant to (K, = 60 sec-1). Design an appropriate compensator to meet all the performance specifications.? B) Check the stability of this system with compensator and without it? (
A unity feedback system is shown in Figure Q1. R(s) C(s) K G(S) Figure Q1 Given that K(s-4s +8) G(s) = (s+4)(s +10) %3D From the given open-loop transfer function, G(s) detemine the following: ) The imaginary erossing of the root locus of the closed-loop transfer function. Hence the gain at that crossing. (i) The arrival angle of the root locus of the closed-loop transfer function. (iii) The breakaway point of the root locus of the closed-loop transfer function is given as s=-6.05. Hence, determine the gain at that point. (iv) Using the information gathered from (i) until (ii), sketch the root locus of the closed- loop transfer fiunction. (v) Hence determine the range of gain K for the underdamped stable system and the critically damped system.
Do b)
Copy the control system shown in Figure Q2 into your answer book, labelling the actual output, control signal, desired output, plant, feedback and error signal. Q2 (a) 2 Σ K+ K, (s+1)(s+2) Figure Q2 (b) Determine the closed-loop transfer function for the system shown in Figure Q2 and hence obtain the characteristic equation for the system. Using Routh 's stability criterion, find the range of the controller gains (K, Ki) for which this system is stable. (c) For the system shown in Figure Q2, find the frequency, jo, and gain, Kı, for which the root locus crosses the imaginary axis (assume K = 1). (d) (e) What would you expect to see for the frequency, calculated in part (d), when you decrease K below 1.
Q1) A closed loop system is shown below the input is R(s) and the output is Y(s) (s + 1) (s + 4) 1 1 (s – 3) Y(s) a) Determine the closed loop transfer function R(s) b) Derive the equivalent state space model c) Hence from the state space model Sketch a block diagram model for the system
i need the answer quickly
In the feedback system shown in Figure Q3, the controller and the plant have the following transfer functions respectively: (s+4) (s+1)(s+2)(s+3) G.(s) = K>0 and G,(s) = Answer the following for this feedback configuration: a) Calculate the closed-loop transfer function. b) By using the Routh-Hurwitz criterion find the values of the controller gain K such that the closed-loop system is BIBO stable. c) Compute the steady-state error to a unit step reference input as a function of the controller gain K. d) Assume now a PI controller G.(s)=K, 1+ is used instead of the constant gain K. Ts Calculate the steady-state error to a unit step reference input. Is your result in agreement with the "internal model principle"? R(s)+ E(s) Y(s) G.(s) G,(s) Figure Q3: Unity feedback system
I need the answer as soon as possible
Q6: Obtain the transfer function Y(s)/R(s) for the closed loop system shown in figure (6). Use signal flow graph (Masons gain formula) method. G:(s) G(s) R(s) C(s) G,(s) G2(s) G;(s) Figure (6) G,(8) G,(s)
Will upvote!