Determine the normal stress developed in the rod at points A, B and C. Each segment of the rod has solid circular cross section with the diameter indicated in the figure. 1.6 in 0.8 in 1.0 in A• B 2 kip 3 kip 8 kip 7 kip

Determine the normal stress developed in the rod at points A, B and C. Each segment of the rod has solid circular cross section with the diameter indicated in the figure. 1.6 in 0.8 in 1.0 in A• B 2 kip 3 kip 8 kip 7 kip

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A thin strap is wrapped around a solid rod as shown in Figure 1a. Determine the principal stresses and maximum in-plane shear stress, and average normal stress, and also the equivalent state of stress of the element H on the strap as shown in Figure 1b, when oriented 45° clockwise. 10 MPa Figure la 5 MPa Figure lb
The solid steel rod (1) shown in the figure has an allowable shear stress of 3 ksi. The brass tube (2) has an allowable shear stress of 8 ksi. The outside diameter of the tube is D2 = 1.63 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B.Calculate(a) the largest torque T that can be applied at the upper end of the steel rod if the allowable shear stress in tube (2) is not to be exceeded.(b) the corresponding minimum diameter d1 required for steel rod (1).
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 25.7 ksi, Sy= 3.7 ksi, and Sxy= 6 ksi. Assume ß = 38°. Determine the normal stresses o, and o, and the shear stress Txy at the point. Sx Txy Answers: 0x = Oy = Txy = ox B ksi. ksi. ksi.
A state of stress is specified in the figure shown below. Determine the Normal stress oy (mPa) on the Principal Plane if P1 = -9mPa; P2 = 47mPa and v= 25mPa P1 P2
Given: X= 269.6mm^2
If P = 8.571 kN, determine the stress in member CE assuming that the area in steel is 24 mm^2. *DRAW THE FREE BODY DIAGRAM *COMPLETE SOLUTION *3 decimal places ALL ANSWER
Q1) (A) Two solid circular cross-section bar as shown in the Figure. If the stress in left portion is limited to 150 MN/m2, determine the diameter of the left portion(D). Find also the length of the right portion(a) if the total elongation of the bar is to be 0.2mm. Young's modulus is E = 210 GN/m². (B)If, in order to reduce weight whilst keeping the external diameter constant, the left portion is bored axially to produce a cylinder of uniform thickness, whatis the maximum diameter of bore possible given that the maximum allowable stress of the left portion is 180 MN/m2? The load can be assumed to remain constant at 160 kN. 0.03 m 160 kN D 160 kN diameter a 0.4 m
The block shown in Figure 2 is subject to three forces. a) Determine the normal stress at point A. b) Determine the normal stress at point B. DICE: b = 100mm; b ’= 50mm; d = 75mm; d '= 125mm; P1 = 500N; P2 = 1250N; P3 = 250N. Disregard the weight of the block. Please show me step by step. I know the answer, but I don't know how to get to it. The answer that I have is TA = -0.1703Mpa and TB = - 0,0977MPa. So can you, please, how to get these answers.
The solid steel rod (1) shown in the figure has an allowable shear stress of 18 ksi. The brass tube (2) has an allowable shear stress of 6 ksi. The outside diameter of the tube is D2 = 1.50 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Calculate (a) the largest torque T that can be applied at the upper end of the steel rod if the allowable shear stress in tube (2) is not to be exceeded. (b) the corresponding minimum diameter d1 required for steel rod (1). Rod (1) Tube (2) B D₂ IT -d₁ Fixed plate End plate
The curved bar shown in the figure has a rectangular cross section of 50x75 mm and an internal radius of 125 mm. For a force F = 1200 N, determine: a-) the normal stress at point A. b-) the normal stress in point B.
The d = 12-mm-diameter solid rod passes through a D = 21-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 10 mm. The rod head has a diameter of a = 29 mm, and the head has a thickness of t = 12 mm. If the normal stress produced in the rod by load P is 100 MPa, determine(a) the bearing stress acting between the support plate and the rod head.(b) the average shear stress produced in the rod head.(c) the punching shear stress produced in the support plate by the rod head. Calculate the cross-sectional area of the rod.Answer: Arod = mm2 Calculate the tension force in the rod.Answer: Frod = N Calculate the contact area between the support plate and the rod head.Answer: Acontact = mm2 Calculate the bearing stress between the support plate and the rod head.Answer: σb = MPa Calculate the area subjected to shear stress in the rod head.Answer: AV-rod head = mm2…
A punch for making holes in steel plates is shown in Figure 3. Assume that a punchhaving diameter d = 20 mm is used to punch a hole of 8 mm plate. If force, V = 110 kNis required to create the hole, determine the shear stress in the plate.