Only handwitten answer is needed Determine the normal force, shear force, and moment at point C.Take that P = 12 kN and w=8 kN/m.(Eigure 1)FigureW< 1 of 1-1.5m-1.5m +1.5m +15m-B▼Determine the normal force at point C.Express your answer to three significant figures and include the appropriate units.No= ValueSubmitPart BVc = ValueSubmitRequest AnswerDetermine the shear force at point C.Express your answer to three significant figures and include the appropriate units.Part CMc =Request AnswerKNValue4KNDetermine the moment at point C.Express your answer to three significant figures and include the appropriate units.?kN m??

Answered: Image /qna-images/answer/04329be2-fcda-41a3-8165-3d15e48160e0.jpg

Determine the normal force, shear force, and moment at point C. Take that P= 12 kN and w=8 kN/m.(Figure 1) ▼ Express your answer to three significant figures and include the appropriate units. Nc = Submit Part B Value Request Answer 1 kN Determine the shear force at point C. Express your answer to three significant figures and include the appropriate units. f ? 2

Determine the normal force, shear force, and moment at point C. Take that P= 12 kN and w=8 kN/m.(Figure 1) ▼ Express your answer to three significant figures and include the appropriate units. Nc = Submit Part B Value Request Answer 1 kN Determine the shear force at point C. Express your answer to three significant figures and include the appropriate units. f ? 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Need only correct answer . I will vote.
Match the given functions with the components of a wind turbine. Connects the rotor hub to the gear box Choose. Covering of the wind turbine's generating components Choose.
Gentlemen, please help to solve a,b,c as I faced confusing questions about screw jack. Conditions are: screw jack is lifting 3.2 tonnes, screw pitch is 12 mm, diameter of the screw is 5 mm. Coefficient of friction was not given but I think we will need it for total force calculation, lets take it 0.2. a) Calculate horizontal component to move the load - what is ment here by horizontal component? b) Calculate vertical component to move the load - what is ment here by vertical component? c) Total force needed to move the load with a lever of 0.82m d) Velocity ratio (VR=distance by effort/distance by load) Distance by effort (lever)=2 x 3.14 x 0.82 = 5.15m Distance by load = pitch= 12mm= 0.012 m VR=5.15/0.012= approx 429. e) Calculate efficiency. For this we need to have MA (mechanical advantage). It can be calculated when we know total force. Efficiency=Load (3200 x 9.8) / effort
Please solve all three.
Solve correctly please.
need Z. Need only handwritten solution only (not typed one).
To convert an arc to a circle: a. Use the FILLET command with a 0 radius b. Use the EXTEND command c. Use the LENGTHEN command d. Use the JOIN command
can u solve the question using newton or lanrnage method in detail with hand written notes
Where did you get the 3 from for the distance of q?
1.2 Please select all the correct statement blow. A. Retaining rings are inappropriate to retain hubs and bearings onto shafts. B. During shaft design, the locations with the minimum torque and moment should be identified. C. A rivet can always provide a much stronger attachment than a bolt or screw of the same diameter. D. Power screws are used to convert the rotary motion of either the nut or the screw to relatively slow linear motion of the mating member along the screw axis. E. Single-row ball bearings (as shown in the figure below) can carry a significant amount of trust load and can carry more trust load than roller bearings (as shown in the figure below). single-row ball bearing Explanation: roller bearing
*NOTE ON INSTRTUCTUONS AND HINTS
cannot get the right answer using this method.