Determine the moments of inertia of area with respect to centroidal axis parallel to y-axis as shown in Figure Q2. 12 cm, r= 12 cm r= 5 cm 14 cm 55° [7 cm X 51cm 7 cm

Q: A hydraulic jack has a 2-inch diameter input piston and a 2-inch diameter output piston. If a 300 lb…

A:

Q: Q) Find Xc and Ye angle 10 m 20m 25 m

A: The Center of mass is a point where the sum of the moment of the weight of each particle is zero. It…

Q: A torque of 18 N m is applied to a rotating part. The part has a moment of inertia of 0.078 kgm2.…

A: Here we will use the the torque equation and the rotational motion equation.

Q: Evaluate the following statement and determine whether it is True or False: "The specific heats for…

A: Specific heat (often denoted as "c") is a thermodynamic property that describes the amount of heat…

Q: A 7 mm diameter copper bar is to be cold worked 69 %. Find the final diameter (mm). Round your…

A:

Q: can someone draw figure for this based on the solution given

A:

Q: Answer the following

A: Draw the free-body diagram of the reach-stacker with the arm.

Q: Solve with the correct unit 4. A cylindrical tank is 50 in. long, as a diameter of 16 in.and…

A:

Q: An 18 teeth sprocket driving with 98 teeth sprocket at a center distance of 34 pitches. Find the…

A: Approach to solving the question: Detailed explanation: Examples: Key references:

Q: How did you calculate the 233.33 on the second part for the height from the end of the rod DE to the…

A:

Q: If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the…

A:

Q: Determine the critical load for a pinned umn made of a circular bar of SAE 1020 hot-rolled steel.…

A: Given   Length, L = 800 mm Diameter, d = 20 mm For SAE 1020   Young's modulus, E = 205 GPa Find…

Q: Solve 0.782bar in p/q form

A: Given that : x = 0.782782782....... We need to find it in the form of p/q

Q: please calculate at least 3 decimal places a) Draw a sketch where you replace the distributed…

A:

Q: Cork k =.045 also all are 300 K values ... please resolve

A:

Q: The wind velocity on the upstream side of a wind turbine is 5.2 m/s. If the turbine extracts 31% of…

A:

Q: 3. Two cables are attached to a telephone pole as shown below. 15°T 800 lb 900 lb a) If the…

A:

Q: ។ 2 KN G lom 10KN-M B 6m 8m IKN ях find torque about AB

A: Given DataP=2kNPo=1kNM=10kNm

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: A force of 400 N is exerted 20 cm from the axis of rotation. What is the resulting moment of force?…

A: The moment can be defined as the product of the distance from the axis of the force and the…

Q: Q4 Locate the cenroid -12 in. -12 in - 15 in. 15 in. 25 in. 9 in.

A: we know that the centroid of a right circular cone is at  a distance of  14th of its…

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: Rc is -178.25 Ib. Why in the formula it's 17825 ?

A: The value of RC is represented as : Rc=-178,25 =-17825 lb The negative sign denote the direction…

Q: Solve for the stress of a plate (in Pascals) in order to punch a hole 20mm diameter that is 25mm…

A: Given data: d=20 mmt=25 mmF=550 kN Need to determine the stress (shear stress) in the plate.

Q: If the torque and speed values are 125 N-m and 1800 revolution per minute, then the power required…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: What is the weight of 3 slug, expressed in pounds-force? o 96.522 lbf

A: Given      Weight = 3 slug

Q: 1. In the given figure, gear 1 has 24 teeth and gear 2 has 70 teeth of PD=4. Gear 3 has 20 teeth and…

A:

Q: Q2. Figure Q2 shows a simple gear train. At the instant shown, a force F = 1100 N is applied at one…

A: Force F=1100 NTeeth on gear ATeeth on gear BLength of the leverMoment of inertia of the gear A…

Q: Q/Find the value of T (kN. m/m) So that the value of angle of twist at D equal to zero.

A: The elemental angle of twist for the shaft CD can be expressed as, On integrating the above…

Q: Q4) Find FA and FB loads using your student number considering Figure 1. (Last two number and add…

A:

Q: I want to buy a two METAL SPUR GEAR for my 2 pieces of G.I pipe with an 3 inches diameter (3mm…

A:

Q: Answer with True or False of the following question: 5. For a fluid at rest, the shear stress is…

A: 5 . For a fluid at rest, the shear stress is zero. True.   When we apply shear stress on solid it…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: Step 1:a. Equation for the differential area aligned horizontally The differential area element dA…

Q: 2 Find T: For q=-KA when dr

A: