determine the maximum shear stress within

Q: A 1.5 mean diameter flywheel, 600kg weight changes its speed from 240 to 230rpm during shearing…

A:

Q: Von mises and tresca agree in pure shear

A: In machine design, mainly five failure theories are used to relate stress with the strength of…

Q: The drilling time (in minute) is

A: Given, Diameter,d= 20 mmThickness,t= 40 mm N= 400 rpmFeed rate,f= 0.1 mm/revDetermine the drilling…

Q: While solving problems using the average normal and average shearstress equations, why is the…

A: While calculating average shear stress, theoretically, the flaws in the system are not taken into…

Q: Q.06 A ircula hole of20 m diameteris to e poduce inashe of mm thckes.The lerance allowance between…

A: Given: Hole diameter, d = 20 mm Sheet thickness, t = 4 mm Clearance allowance= 3 %

Q: 1. Give 4 examples of nonferrous material? 2. Explain creep with example ? 3. Explain Bending…

A:

Q: city 8f steadily decrease from entrance to exit. ii. Rolling is most effective in the absence of

A: The velocity of the sheet increases from the entry of the roll to the exit of the roll. It helps in…

Q: Draw the shear force and bending moment diagram for the loaded beam shown below. Also mark the…

A:

Q: How does torsional stress and angle of twist impact engineering design?

A: Importance of torsional stress in Engineering Design:- Torsional stress is induced in an element due…

Q: A 1 hydrostatic extrusion 2 Strain hardening 3 High temperature 4 Anisotropy in blank metal 5 n=0 6…

A: Answers of B from A are as follows in order from top to bottom: 5,6,15,14,12, 2, 11, 7, 8, 13, 16,…

Q: What exactly is meant by the term "shearing stress"?

A: Given question: What exactly is meant by the term "shearing stress"?   The given question is related…

Q: A worker in a large welding and steel fabrication shop asked his employer if he could make a trailer…

A: A trailer hitch is used to connect the trailer or any loaded cart with the pickup truck with the…

Q: -4 cm inner diameter from

A:

Q: How was the shear formula derived?

A: Shear Stress: This is the ratio of force acting per unit area of an object/component.  This is…

Q: Identify and explain the method of milling process in which the stresses on the teeth is maximum at…

A: The milling process in which the stress on the teeth is maximum at the end of the cut is the up…

Q: Q1/ A cuber of the type of open-end đies arranged in a ring, has 66 dies, 32x32x150 mm. a-Calculate…

A: Turning operation is the manufacturing technique that is done on a lathe machine. In this operation,…

Q: (a) A teacher, design supervisor, examining a design of a student, point out to him that the shaft…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: Are the shafts often subjected to loads applied to attached pulleys and gears?

A: The pulleys and gears are used for power transmission through shafts. This power i.e torque…

Q: Since both the force that cause Bearing Stress to Normal Stress is perpendicular to the cross…

A: Stress : When a material is subjected to an external influence (Force, moment, Torque etc) a…

Q: 4. In rolling operation, large diameter roll induces.. on the surface of the rolled part. b. tension…

A: Explanation : During rolling operation , due to rolling extrusion force applies over the surface to…

Q: If the number of fatigue is smaller than the number of yield, would that be safe or not? and why?…

A: When machine parts are subjected to fluctuating loading it is called an fatigue, repeated or…

Q: ng stres ng stress

A:

Q: 1. Give 4 examples of nonferro material? 2. Explain creep with example 3. Explain Bending Stress…

A: Hi and thanks for the questions. Since you have asked multiple questions, we will solve the first…

Q: Can the External forces be applied to a body as distributed or concentrated loadings?

A: Yes, external forces can be distributed or concentrated.

Q: Raw material with an input speed of 3.1 MIS will be rolled to the rolling mill with a plate-shaped…

A: Metal forming is a manufacturing process in which the raw material is deformed plastically to get…

Q: 110 rpm driven by 500 mm diameter flat rolling electric motor available on rolling mill are rotated…

A: Given data: The speed of the rolling mill is the N = 110 RPMThe speed of rollers in rad/s will be…

Q: Aluminium and copper wires can be made by cold drawing process. Select one: True False…

A: Solution:

Q: Find the angle of bite

A: Given; In single pass rolling bearing process using ;Diameter,d=510 mm  R=255 mmwidth,W=110So,Acc.…

Q: What percentage of strength of a solid circular steel shaft of 160 mm diameter is lost by boring 100…

A: Given data as per question Diameter of solid shaft =160 mm Axial hole diameter =100 mm

Q: Q3B) A metal is fabricated by drawing at 125 °C. The metal melting temperature is 400 °C. Find by…

A: Given dataFabricated Temperature (T)   (a) Working Temperature=125°CMelting Temperature=400°C Tm

Q: 30 KN A 1m B 3 m 50 KN 2 m D

A:

Q: A blanking operation is to be performed to create the part shown below out of 2-mm thick half- hard…

A: Given: To find: Punch dimensions Die dimensions Blanking force

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.