Determine the maximum negative shear at C. 4.5m. 4.5m. Pa45 kN O zoom image 38.75 kN 58.43 kN

Q: What is the overall density? %

A: This question is related to the Soil Mechanics from Civil Engineering.

Q: The ∑ F proceeding in the couple is?

A: Brief concept- Couple- It is a pair of equal and opposite parallel forces. These two forces do not…

Q: Is y = 2x?a solution to the differential equation % x²y'" – xy' + y = 0? No O Undefined Yes

A: Given, y = 2x2 is solution of equation 0.5 x2 y" - xy' + y = 0

Q: A triangle has an area of 14 sq ft and a base of 7 feet. What is the height of thetriangle?

A: given data :  area of triangle (A) = 14 square feet  base (b) = 7 feet  height (h) = ?

Q: max = Amax=

A:

Q: 2.107 How many bridge hands are possible contain- ing 4 spades, 6 diamonds, 1 club, and 2 hearts?

A: Given, number of spades =4 number of diamonds =6 number of club =1 number of hearts =2 Total cards =…

Q: How can I find GH, EG and FH

A:

Q: how did you get 1.5 for the first part

A: In the original question it is stated that Vmax=2 Vmin In the solution, the following is given.…

Q: Give the equation for Cunningham correction factor.

A: where C =correction factor λ =mean free path d = particle diameter An are experimentally determined…

Q: complete the following set of profile level notes and show the customary arithmetic check.

A: Height of instrument method:HI=Elv+BMElvi+1=HIi-FS or ISExampleHI at BM-a:HI=234.51+1.24=235.75Elv…

Q: Only Draw profile with appropriate scale

A: To draw the profile to the given levelling

Q: GIVEN: = 43.6°, AB = 55.2m, Hi = 1.4m REQUIRED: H 38.66m 38.97m 39.47m 39.97 A Ø Hi H B

A: Given data:- The given angle, φ=43.6° The Length of AB is, 55.2 m The value of Hi, =1.4 m

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: 10 divisions of vernier scale are equal to 11 divisions of a main scale of each 0.1 mm. What is the…

A: Given data- 10 divisions of vernier scale=11 divisions of main scalemain scale one division=0.1 mmTo…

Q: Which of the followings does not help to produce good-quality technical sketches and drawings? a)…

A: Eraser: if we are using the eraser more frequently then the quality of drawing will decrease. Pens:…

Q: 05 Find the XT 0.5 1.5 3 2.5

A:

Q: Draw the influence lines for the vertical and horizontal reactions, Ax and Ay, at support A and the…

A: Question consist of truss supported at hinge support at A and G . Length of members are given in the…

Q: why 3.5 instead of 2.5?

A: Correct solution is provided below

Q: Kindly solve this question under Measurement and Specifications for Civil Engineers.

A: Based on the information provided and the Contract Specifications, here's the takeoff for the…

Q: What do you mean by specific collecting area in an ESP?

A: Solution: The specific collection area is basically the area of the gas of flue through the…

Q: Determine total indeterminacy

A:

Q: 1. Ah = [ Select ] 2. Av [ Select ] 3. MA = [ Select ] %3D 4. C, = [Select ] 5. Dy = [ [ Select ] 50…

A:

Q: 80 38 24 340 R24 25 R40 130

A: It is not possible that every command and steps that is used in the drawing is to write down here…

Q: I x,0= 10 " I yo = r x,0 = 4"X6"X ½" r yo = 12" 4"X 8"X 1" | 1" 12 "

A:

Q: me miller indices.

A: Given figure

Q: Q4: Convert the following into required: 1- An area 4.2 cm on amap with scale 1/5000 > Don , Olk,…

A:

Q: Express all denominate numbers 8 gal 3 qt  35 qtin the same unit.

A: Solution:-

Q: Part A What is the ratio scale for the equivalent scale of 1 in. = 80 ft? Express your answer using…

A: 1 ft =12 inch given 80 ft =12*80=960in Ratio scale=112×80=1:960

Q: Why is the F1y = 400lb?

A:

Q: 30 10 30 10 15 20 15 10

A: Line command of autocad is used  We can use either absolute coordinate method or relative coordinate…

Q: St BS 0+00 3.54 0+10/ 0+20 1 1 1 1 I 2.994 2.044 0.171 00249 1.497 IS 3.269 2.966 Fs 1.845 1.840…

A:

Q: Draw the figure to an enlarged scale in Isohyetal method

A: The iisohyetal approach is a technique for calculating the average amount of precipitation within a…

Q: sanitary engineering  solve by hardy Cross method  k=8*f*L/pi*g*D^5 f=0.02 g=9.81 pi=e.14

A: Given data in question  Length of pipe  Diameter of pipe Constant value of f Acceleration due to…

Q: 2ft

A: Given  Triangle of height 2ft  Slope : 3H to 4V

Q: من الله 유 | 3klf 20 ft Mmax=

A:

Q: Complete the table below. LINE BEARING DIST (M) AB N 60° 15.3' E 40.311 BC S 64° 5.6' E 38.910 CD S…

A: A closed traverse ABCDEA is given. The fore bearing and distance of each line are mentioned. To…

Q: Comparison between Davis, Penck, King's model.

A:

Q: A circle of diameter d = 200 mm is engraved on a brass plate (see Figure 2). The plate has…

A:

Q: 4 cm 0 2 י 5 cm 4 567 Value: cm 10 5 150 Value: mm 0 140

A: There are two scales, and the values shown on the two scales are required.One is the main scale and…

Q: End Area (ft2) Volume (yd) Volume (yd) Net Volume (yd) Station Mass Shrinkage Total Cut Fill Cut…

A:

Steel Framing

A steel frame consists of a skeleton frame structure comprising of horizontal I-beams and vertical steel columns fitted in a rectangular grid building construction to brace the floors, walls, and the roof of the building held onto the frame. Due to the implementation of this methodology, the construction of the skyscrapers was feasible.