Determine the maximum compressive stress in the bracket at section a-a when the load P = 25 kN is applied at %3D x = 300 mm. P 15 mm 15 mm 200 mm 150 mm Lütfen birini seçin: a. -104.17 MPa b. None C.-95.83 MPa d. -54.17 MPa e. -45.83 MPa

Q: Problems. 1 Determine the required 1.5m cross-sectional area of t the bar BC if allowable 1.5m…

A:

Q: The steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. is carrying a load P=…

A:

Q: 2 m hollow cast iron pole has an outside diameter of 250 mm and a thickness of 10 mm. The pole is…

A: Given Data P=15 kN D=250 mm t=10 mm

Q: H.W 1 The bracket plate is 40 mm thick. b= 272 mm. Load on the bracket, P= 100 kN; spacing, C (…

A: 1. Draw a diagram for the given cross-section. Here, A, B, C, D, E, F indicate the shown rivets, Fp…

Q: A cantilever consists of 8 cm x 8 cm x 10 mm angle with the top face AB horizon- tal. It carries a…

A: We have a cantilever with an 8 cm×8 cm×10 mm angle and an AB horizontal top face. It supports a…

Q: find the bearing stress between bolts and plate 10/-.. 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN…

A: Given data  diameter of bolt (d) = 10 mm thickness of plate (t) = 8 mm  Load acting on the plate…

Q: 36mmø CISE NO. 1 (REACTIONS) 50deg C A Support 6m 4m 5 RA 12 1. Compute the stress in the support at…

A: Given: The value of force is W=107 kN. The diameter of wire is d=36 mm. Determine the equation for…

Q: The bellcrank is in equilibrium a) determine the diameter of the bar DE if the normal stress is…

A: GIVEN: Load W= 30KN length of road BC:LBC=0.2m length of road CD:LCD=0.3m  thickness of plate C: t=…

Q: PLEASE ANSWER QUICKLY

A: Given data as per question Diameter = 2 in Length of bar =24 in Force = 20000 lb

Q: Q1: The C-shaped steel bar has cross section of a square of side 1.6 in. If the magnitude of…

A: given data  force p= 2 kips dimension of cross section= 1.6 ×1.6 in^2 find the combined stress at…

Q: Link AB, of width b= 2 in. and thickness t = in., is used to support the end of a horizontal beam.…

A:

Q: Determme the snallest allowable diameter of the solded shuft ABCD, knowng that the allowable shear…

A: Given data as per question Allowable shear stress = 60 Mpa The radius of disc B =80 mm…

Q: 2. Determine the shear, tensile and bearing stresses on a double riveted butt joint with ¾ in. main…

A:

Q: 1) Consider the frame below. 4 kN/m 20 mm D 60 mm B E 20 mm D. 50 mm |-1.5 m --1.5 m -† - 3 m 5m 3 m

A:

Q: Q3/ If two members, A and B, are connected together and fixed supported at one end. The tensile load…

A:

Q: Problem I. In a high-rise building construction, a boom is being used to efficiently transport…

A:

Q: A bar with an allowable tensile stress of 16 ksi has two holes at A and B. Determine the maximum…

A:

Q: 2. Determine the shear, tensile and bearing stresses on a double riveted butt joint with ¾ in. main…

A:

Q: a. There is no shear stress, only hydrostatic compressive normal stress in all directions b. At the…

A: Given Two spherical bodies passed

Q: A hole is to be punched out on a layer of papers using a puncher with a hole diameter of 100 mm. If…

A:

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: The 7/8-in.-diameter pins at A and C that support the structure are in single shear. Find the…

A:

Q: Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 53 kN if it…

A:

Q: in A Composite bar Çansists af QI) an aluminum Section rigidly fastened between as shown in fiqure…

A:

Q: Determine the reaction loads and maximum shear stress ! 200 Ibf-in z-in dia. A B 4 in 6 in

A:

Q: An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are…

A:

Q: digit of your ID No., mm) and 10 mm thick (plus quarter of the last digit of your ID No., mm). It…

A:

Q: 1. A picce of wire 10-in long is tied vertically. The wire has a diameter of 0.1-in and is used to…

A:

Q: 6. A PIPE CARRY|NG STE AM AT 3.5 MPa HAS AN OUTSIDE DIAMETER OF 450 mm AND A WALL THICKNESS OF 1D…

A: force, F=σ×AF=3.5×π4×4302F=508270.42 NP=F

Q: PART 2 : COMPUTE THE AXIAL STRESSES IN ALL MEMBERS OF THE TRUSS SHOWN. USE 300 sq. mm AND 250 aq. mm…

A: Remark: As per the guidelines only the first three subparts will be answered. You can ask other…

Q: determine the diameter of the bar DE if the normal stress is limited to 100MN/m2. b) Determine the…

A: Given DataP1=30kN θ=30° {taken}

Q: Q2: The 20-mm-diameter bolt fastens two wooden planks together.. Find the smallest thickness of each…

A:

Q: Q1: determine the increase in vertical stresses at depth of Z=3.5 m under points A, B and C due to…

A:

Q: A truss was made of circular hollow steel with an outside diameter of 100 mm (plus half of the last…

A:

Q: 1. A steel rod that is 5.5 feet long, stretches 0.04 inches while under a 2-kip tensile load. a.…

A:

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A:

Q: The internal drag truss for the wing of a light airplane is subjected to the forces shown. Determine…

A:

Q: compute the maximum stress in the member, considering stress concentrations.

A:

Q: 4. A load of 25 KN is to be supported by three equidistant vertical rods as shown. At first, all the…

A: To find: The stress in the rods. Given: The young modulus of steel is Esteel=205 GPa and Ecopper=100…

Q: A crane is supported by two cables with a cross-sectional area of 3.04 cm2 each. Determine the…

A: A=3.04cm2 = 304mm2 Assume P=20KN , Mass of the boom = 450kg

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.