Determine the maximum axial compression service load that can be supported by the column shown in Figure 1 if the service live load is 3 times bigger than the service dead load. Check that HSS 8x4x4 is a nonslender-element cross section and then use ACI Equations E3-2 or E3-3. 12 feet TMM HSS 8 x 4 x 1/4 ASTM A500 Grade B Figure 1

Determine the maximum axial compression service load that can be supported by the column shown in Figure 1 if the service live load is 3 times bigger than the service dead load. Check that HSS 8x4x4 is a nonslender-element cross section and then use ACI Equations E3-2 or E3-3. 12 feet TMM HSS 8 x 4 x 1/4 ASTM A500 Grade B Figure 1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 4: A W12x106 simply supported beam carries a uniformly distributed load. The properties of the section relevant to the problem are as follow: Use A50 steel and Cb - 1.14 d - 328 mm bf-310 mm tf = 25.1 mm tw = 15.5 mm kdes - 40.4 mm ry - 79.0 mm lx = 388 x 10^6 mm^4 ly - 125 x 10^6 mm^4 Sx - 2380 x 10^3 mm^3 Zx=2690 x 10^3 mm^3 J-3800 x 10^3 mm^3 Cw=2870 x 10^9 mm^6 1. Which of the following nearly gives the Design Strength Moment (LRFD) if the span of the beam is 2.5m? 878 KN-m 793 KN-m 836 KN-m 811 KN m
7:49 ll ? 1 Gmail h.w. 1.jpg A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Fig. Axial loads are applied at the positions indicated. If P 3000N and the cross sectional area of the rod is 325 mm2, determine the stress in each section, and total deformation of the road. E for steel is 200000 MPa, E for aluminum is 70000 MPa, E for bronze is 100000 MPa 4P Steel Bronże O | Aluminum PO D.9 ~回

Please solve the given below and show your complete solution.
The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.1mm shorter than the steel posts at temperature of 50°C, if the allowable compressive stress in steel is limited to 120 MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10°C ?
For the box beam shown in Fig. if the modulus of elasticity E = 200 GPa, the flexural stresses at support for point (a) is ..................... MPa * 120mm 16.2kN 16.2KkN —{ 10.2KN/m £ fj//’/ £ W @ Q| im 3m im = 30 mm thickness of walls cross section Your answer
Of a reinforced concrete column under pure axial load given its cross-section dimensions, a) Determine the total longitudinal reinforcement area of the section you are reinforced according to the ratio of Ø18 reinforcements and the minimum reinforcement. b) Calculate the amount of axial load that the section can bear. m=1,n=4 Cover value will be taken as 35 mm. For the material, it will use C25/30 – S420
For the hollow beam. Calculate the design. capacity, As = 2040mm ² Fy = 420 Mpa,Fc=25Mpa,Asmin check is not required
: Describe with the help of diagram , why the rate of strength gain of C3S , C3A , C2S and C4AF is different ?
A compression member AB (HE 400 B) is pinned at both ends and braced in the weak direction as shown in the figure. Material and geometrical properties are given below. For the given loading and ASD load combination (PG+Pq=3500 KN), determine whether the section is satisfactory or not. Material: 5355 F355 MPa F 510 MPa E= 200000 MPa Section properties (HE 400 B): A: 19780 mm² d: 400 mm h: 298 mm t: 13.5 mm. tr: 24 mm b: 300 mm i,: 170.8 mm İy: 74 mm B X -BRACING IN THE WEAKDIRECTION
Please answer the problem below, using NSCP 2010/2015,Using 4 decimal. 16-28mm diameter bar
How to solve this question step by step
5 5a 5b 5c Alaterally supported beam was designed for flexure. The beam is safe for shear & deflection. The most economical section is W 8 x 13 however the said section is not readily available at the time of the construction. If you are the engineer in charge of the construction what alternative section will be the best replacement? Why? Use: Fy=248 MPa: E=200,000 MPa Designation Ag (mm2) Weight kg/m 1910 19 30 width 24 flange. thickness d (depth) mm 200.41 bf 100.06 W8 x 10 4.32 15 expla'n briefly your cho'ce. (transform your comparative analys's 'nto a narat've form to support your cho'ce) W8 x 13 2477 202.05 101.60 6.48 W6 x 20 3787 157.48 9.27 152.91 102.36 W6 x 16 3058 159.51 10.29 tf Web 5.21 thickness tw Elastic Properties mm 4 Ix x 106 mm 3 Sx x 103 5.84 6.60 6.60 13 16 17 13 126 162 220 167 mm rx 81.79 81.53 67.56 66.04 mm 4 lyx 106 1 1 6 2 mm 3 Sy x 106 17 22 72 36 mm ry 21.36 21.41 38.10244 24.54 Plastic properties mm 3 Zx x 103 145 187 244 192 mm 3 Zyx 103 27 35 110 56…