A 210 kN axial compressive load is applied to a W530x101-steel column with the length of 3.20 m and cross sectional area of 12900mm2. The modulus of elasticity of this steel is 203 GPa. a) Find the stress acting on the column. b) Find the length change of the column under this load.

A 210 kN axial compressive load is applied to a W530x101-steel column with the length of 3.20 m and cross sectional area of 12900mm2. The modulus of elasticity of this steel is 203 GPa. a) Find the stress acting on the column. b) Find the length change of the column under this load.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: When solving the problems for Section 1.6, assume that the material behaves linearly elastically.…

A: Given data in question Diameter Elasticity modulus Poissons ratio To find out Largest force P

Q: A composite beam is made of two brass [E = 110 GPa] bars bonded to two aluminum [E = 71 GPa] bars,…

A: Bending moment=260Nm a=10mm b=85mm c=20mm d=55mm

Q: The ratio of hoop stress/axial stress is? O 1/2

A: Hoop stress is also known as circumferential stress . It is tensile in nature acting along…

Q: 7. A solid aluminum cylinder is placed within an ASTM A501 steel tube as shown. Compute the stresses…

A: Given Data: The diameter of the solid aluminum cylinder is d1=3 in. The diameter of the steel tube…

Q: The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner…

A: Given data, D1 = 35 mm d1 = 20 mm G1 = 41 GPa D2 = 20 mm G2 = 80 GPa L = 430 mm T = 990 N-m To find…

Q: The following terms apply to LRFD (limit state design) and ASD. E. Yield Strength L. Plastic…

A: LRFD - It focuses on developing load and resistance factors. ASD - It focuses on ensuring that…

Q: A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z…

Q: A storage tank of air, 30 inches in diameter, is to withstand an internal pressure of 180 psi with a…

A: Given:- d=30 inches internal pressure=180 psi design factor=3.5 C1020 annealed relative strength=92%…

Q: A composite drive shaft is made up of two sections: a solid steel core and a brass tube encasing the…

A: A composite shaft made of brass and steel.The diameter of the steel part is 80 mm.The diameter of…

Q: A 3003-H14 aluminum alloy rod with 0.5 in. diameter is subjected to a 2000- lb tensile load.…

A: The given data is shown below:

Q: In the section shown, a steel diagonal brace has a tension stress on it (from wind load) = 18.12…

Question

A 210 kN axial compressive load is applied to a W530x101-steel column with the length of 3.20 m and cross sectional area of 12900mm2. The modulus of elasticity of this steel is 203
GPa.
a) Find the stress acting on the column.
b) Find the length change of the column under this load.
For the toolbar, press ALT+F10 (PC) or ALT+FN+F10 (Mac).
BIUS
Paragraph
Arial
14px
A v

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1:- Calculation of stress acting on the column

VIEW

Step 2:- Calculation of change in length

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A beam of the cross section shown is made of a steel that is assumed to be elastoplastic with E=29×106psi and σY= 42 ksi. A bending couple is applied to the beam about the z axis, causing plasticzones 2 in. thick to develop at the top and bottom of the beam. After the couple has been removed, determine (a) the residual stress at y=2 in., (b) the points where the residual stress is zero, (c) the radius of curvature corresponding to the permanent deformation of the beam.
A high-strength steel band saw, 27 mm wide, runs over pulleys 1000 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 350? Assume E =230 GPa. Answer must be in mm.
Solution w/FBD
An SSTM A36 strucural steel beam 3.6 m long is placed between two rigid supports when the temperature is 15 0C. What is the stress developed in the beam if the temperature rises to 50 0C? ___ MPa. Assume that the proportional limit is 235 MPa, and that lateral buckling is prevented. Calculate your answer to 1 decimal place.
The column above is subjected to axial loading only. Assume the following: • E= 29000 ksi G = 10000 ksi • = 986 in4 A = 60 in? • L= 20 ft • Grade 60 steel (60 ksi yield stress) • The column is fixed at the top and pinned at the bottom Which of the following is closest to the maximum normal stress the column can support (before yielding or buckling)? 167 ksi 24 ksi 42 ksi 60 ksi
Sketch the stress-strain curve and explain it in relation to the tensile test for steel bars.
A 1.65m long rod with a circular cross-section is subjected to a tensile load of 50 kN. The rod is made from AISI 1040 hot-rolled steel. The allowable tensile stress is 165 MPa. The rod is permitted to elongate up to 7mm without causing any issues. The proportional limit for the steel is 180 MPa. (A) Compute the required area necessary to meet the stated requirements based on allowable stress. Express your answer in square millimeter units as an integer. (B) Compute the required area necessary to meet the stated requirements based on allowable elongation. Express your answer in square millimeter units as an integer.
According to IS 800-1962 the permissible bending stress in steel slab plate is (b) 1420 kg/cm² (d) 1890 kg/cm² (a) 1500 kg/cm² (c) 2125 kg/cm²
A cantilever beam with cross section shown below and span of 3 m is subjected to concentrated load (P) at the free end. If the maximum allowable tensile stress equals to 10 MPa what is the maximum value of the load P can be applied.
Please solve this question and provide solution
A mild steel bar having 300 mm dia is subjected to shear stresses yielded at a stress of 250 MPa. The maximum value of torque iskNm that can be applied if factor of safety of 1.8 is to be provided.
An alloy steel specimen of 30 mm diameter with a gauge length of 200 mm is load tested. It has extension of 0.16 mm under a load of 85 kN. Load at elastic limit is 160 kN. Young's modulus of the specimen in GPa O 127 O 143 O 150 O 172