Determine the magnitudes of F, and Fyso that the partiele is in equilibrium. Given: F- S00 N O - 45 deg 0z - 30deg Solution: Initial Guesses

Q: A 0.464 how answer choices B 0.537 0.245 Assume the camber line is a circular arc 0.424 38° 0.319 C2…

A: To find: The local diffusion factor.

Q: 28. In a constant volume process, 1.5 kg of air is cooled from 1,200 °K. The change of entropy is…

A: Given data: m=1.5 kgT1=1200 K∆S=-1.492 kJ/°K Need to determine the final temperature.

Q: 9-67. Determine the principal stress, the maximum in-plane shear stress, and average normal stress…

A: Given:σx=350 MPaσy=-200 MPaζxy=500 MPa

Q: 20 kN 16 kN/m B. 2 m 4 m 3. Determine the shear and moment equations for the beam shown. Draw shear…

A:

Q: dr. リ+ y + tan²t – 1 dt dy dt =-+tant 山一位

A:

Q: In the mechanism shown in figure, link 3 is fixed on slider B so it is exactly perpendicular to link…

A:

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: solutions are given, please resolve to get these solutions

A:

Q: Argon in the amount of 1.5 kg fills a 0.04-m3 piston-cylinder device at 550 kPa. The piston is now…

A:

Q: If the speed of the crate at A is 15 ft/s, which is increasing at a rate v = 3 ft/s², determine the…

A:

Q: Please answer The test part d and e From this  problem The test is akredytacji solved thank you

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3 parts. Please resubmit the question…

Q: SHOW COMPLETE SOLUTION PLS NOTE: THE ANSWER IS SHOWN IN THE PICTURE

A:

Q: Find the following. Show complete solution.

A: The given diagram is here, Section 1:- A rectangle OABC, whose sides are 120 mm and 80 mm Section…

Q: Q/ Compute the tension (T) in 1: the cable? Neglect the friction between the cable and the pulley.

A: Given

Q: What is the module of a spur gear with 30 teeth and pitch diameter if 5 inches? 5.236 mm 4.233 mm…

A: The given values are -  Teeth T =30 Pitch diameter D = 5 inch(127 mm)

Q: For the beam and loading shown, determine the magnitude of the maximum normal stress due to bending…

A:

Q: 1.9 Classify the following system of equations: du du dv +6 = 0 at du dv +b+a- dv = 0 at

A: A system of equations is a collection of one or more equations with several variables. The variable…

Q: D. Statics 1. Find the maximum load of the hanging block below to put the system in equilibrium. 2.…

A:

Q: 4. Determine the equivalent stiffness of a linear spring when single degree of freedom mass- spring…

A:

Q: For gear train shown in Figure Determin the output velocity and center distance of the gear train,…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a…

A:

Q: Q2/ Find the weight of the steel ball (A) required to keep the system in equilibrium state as shown…

A:

Q: (x(x+ y) = y(x – y) By homogenous equation solve %3D

A: DE1 (3x2y + 2xy + y3)dx + (x2 +y2)dy = 0 so, M = (3x2y +2xy +y3)  and N = (x2 +y2) dMdy=3x2 + 2x…

Q: the and the angle prom for the resultant of vectors e positive x- axis. Vre any Methud. all answer…

A:

Q: Determine the reactions at the pin support and the applied moment if the bar of Figure 3 has a mass…

A: Given: The mass of bar, m = 50 g The angle, θ = 15° The angular acceleration of bar, α’ = 20 rda/s^2

Q: peom t (つとやr) 8HF1 DETERMINE THE 3 RE he T IONG FOR THE BENM SHOLIN BOVE.

A:

Q: The package that used for pre-processing, analysis, and post-analysis of structures is called :* CAD…

A: Question 1: FEA or Finite Element Analysis is the package used to validate the design virtually. It…

Q: 5 lb lb 2 lb 35⁰ B Resolve the 5 lb force, F, into a component along OA and a component along OB,…

A: Given data:- Force F= 5 lb where OA is inclined =35° from horizontal,  OB descends 3 feet vertically…

Q: Find the V-X and M-X diagrams. For the value of P use 182 kips. show all steps

A: Draw the free-body diagram of section DC. Apply moment equilibrium about point D.…

Q: please solve Q6 asap make sure the answer matches with the given answer. solve without using reduced…

A: Consider the T-S diagram for the regenerative gas turbine power plant.Here, some assumptions are to…

Q: 4. A rigid tank whose volume is unknown is divided into two parts by a partition. One side of the…

A:

Q: FOLLOW THESE STEPS FOR UPVOTE Given Required Diagram Solution Conclusion Do not round off while…

A: At sea levelThe diameter of ballon d=8 indensity of air ρ=0.07498 lb/ft3Pressure P=14.7 psiawhen…

Q: 3. The air in an automobile tire with a volume of 0.53 ft3 is at 90 F and 20 psig. Determine the…

A:

Q: A young man, 22 years old, graduated from college and got his first job. He wants to have a…

A:

Q: 1. A circular step hydrostatic thrust bearing with outside diameter of 16 in. is to be designed to…

A: As per the guidelines, I can solve only first three subparts at this moment. For rest parts, repost…

Q: What is the difference in potential energy per pound of mass of fluid at A and at B. STORAGE TANK…

A:

Q: Find the missing Properties in the following table for water: T [C] V[m³/kg] 300 1 2 3 4 P[kPa] 1600…

A: 1: The properties of steam at 1600 kPa and 300 C from steam table, v=0.158 m3/kgh1=3035.51…

Q: Re = 63 * lo4 if the = 0.25 Re = 63 * De termine ? 169

A:

Q: 1. Write the shear and moment equations and draw the shear and moment diagram. 50 kN/m 100 KN 20…

A:

Q: If 1 Pa is equal to 145 psi, what algebraic equation is needed to find out how many MPa there are in…

A: Given that,  1 Pa = 145 psi So, 1 psi = (1/145 ) Pa So, x psi = (x/145) Pa....... This is algebraic…

Q: can u solve the question using newton or lanrnage method in detail with hand written notes

A: Free body diagram mx¨1+cx˙1+kx1-x2=0 Rearranging mx¨1+cx˙1+kx1=kX2sinωt

Q: Determine the temperature

A: At 200 degree u=2642.9KJ/Kg   h=2855.4 KJ/Kg At T                 u=?                      h=2893…

Q: while draining it. What is the rate at which water has to be pumped in so that it gets fully filled…

A: Given, At a constant rate it takes 30 min to empty the half full tank at a constant rate.…

Q: The machine shown is used for moving heavy items such as pallets of bricks around construction…

A:

Q: Q2) In many modem automobiles cruise control is used to reduce driver fatigue, instead of pressing…

A:

Q: Determine T1 and T2 in N. 45 Tz

A: Given   Weight, W = 50 N          Angle = 45o Find  Tension in the cable T1 and T2

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.