Determine the magnitudes of all pin reactions for the frame loaded as shown. 810 N 395 mm OC B 895 mm 260 630 А D Answers: A = N B = D = N

Q: For the composite areas shown, determine the moment of incrtia with respect to the centroidal ахes.

A:

Q: *2-4. The vertical force F acts downward at A on the two- membered frame. Determine the magnitudes…

A:

Q: The 1 inch diameter shaft is subjected to the loads shown. Draw the "loading diagram" showing the…

A: To findDraw the loading diagram showing the internal forces and moment/Torque acting on a cut…

Q: 80mm 60mm Vax's Gomm 40mm Find the location of the Controid. Show All work. 1

A:

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: *2-72. Two forces F₁ and F2 act on the screw eye. If the resultant force FR has a magnitude of 150…

A: Two forces F1 and F2 act on the screw eye.If the resultant force FR has a magnitude of 150 lb and…

Q: An air bubble rises from the bottom of the well where the temperature is 27°C. Find the percentage…

A: given data-depth of well = 5mT1=25+273=298kT2=27+273=300kP2=Patm=101528Pa≃101528N/m2

Q: Please solve Q8

A: Given data as per question

Q: For given distributed loads, see figures below, determine resultant and moments around load ends…

A: As all questions are different, according to our guidelines we are supposed to answer the first…

Q: Solve for A and B. P=400 lbs. 0=30° P 45° B www Drawing not to scale. Use given angles. Magnitude of…

A:

Q: Q1: water vapour at 500c and (P1). The vapour passes four process as following: 1- constant pressure…

A:

Q: 3. In the figure below two equal forces are applied to the tap wrench a distance d from the center…

A:

Q: u 30° 40° F = 600 N 22

A:

Q: Q1 Derive the torsion equation.

A:

Q: a) Consider a process involving an ideal diatomic where 3 mol, following p = aV, a = 1 x 10° Pa/m³…

A: P=αV ,where α=1×105 Pa/m3 ;Vi=1 m3, Vf=4 m3 ;Pi=αVi=1×105 ×1=105 Pa ;Pf=αVf= 1×105 ×4=4×105 Pa ;So…

Q: 1.14 A steel sleeve of 24-mm internal diameter and 36-mm external diameter 0.4 mm encloses an…

A: The internal diameter of the steel sleeve is d1=24 mm. The external diameter of the steel sleeve is…

Q: Silicon is diffused at 1100°C for 20 minutes with bismuth (Bi). You measure a diffusion length of 1…

A: (d) Write the initial total amount of Bi. Biinitial=2×1015 atoms/cm2

Q: 24. The efficiency of a Carnot engine is 35%. What is the temperature of the cold reservoir if the…

A:

Q: Which of the following gives the reaction at B of the simply supported beam in Newton?

A:

Q: 20 mm Determine the location y of the centroid C of the beam's cross-sectional area. Then compute…

A:

Q: F F An adjustable plier is shown gripping a circular object, where the geometic dimensions a=0.07 m,…

A: For the given adjustable plier  a = 0.07 m b = 0.15 m θ = 35o F = 34.2 N    To determine  The…

Q: Question 2: Saturated liquid water at 20kPa enters an adiabatic pump and discharges at 5 MPa with…

A: Pump Pump is the device which lift the liquid from the lower elevation and transfer it to the higher…

Q: An ammonia compressor is driven by a 20 KW motor. The compressor and the motor RPM are 360 and 1750,…

A: Given, Compressor rpm,Nc=360rpmMotor…

Q: Solve par d,e,f

A: d) 0.0455 kg/se) Waste heat transferred 8.3674 kw    Compressor work input 2.9687 kW…

Q: The force acting on the gear tooth is F=45 KN. Resolve this force into two components acting along…

A: Given, Force acting on gear, F=45KN Free body diagram of the force acting on gear-

Q: from pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The…

A:

Q: Single-plate clutch and spring design of Automotive. Engine Specifications: Power 17.5 KW, Speed is…

A: Given: Power = 17.5 kW Speed = 1000 rpm Shear stress = 40 MPa

Q: This shoulder bolt is composed of hot-rolled monel. The head of the shoulder bolt is a regular…

A:

Q: Fill in all blanks before submission. Round the answer to the nearest integer The figure shows a rod…

A: Given: The length of the rod, L = 6 ft The weight of the rod, W = 100 lb The radius of the sphere, r…

Q: 3-38. The block has a weight of 20 lb and is being hoisted at uniform velocity. Determine the angle…

A:

Q: A 3-kg load in a damped mass-spring system is initially stretched 2m from the equilibrium position.…

A: Given: m - 3 kg x0 - 2 m k - 12 N/m To find: position as a function of time

Q: Solve Q7 only 4) A welded connection, as shown in Fig. 2, is subjected to an eccentric force of 60…

A:

Q: 3. At temperature T₁, the two rigidly connected rods just fit the rigid supports. If both sections…

A: Given data:- Rigidly connected rods To find out:- force stress in AB stress in BC

Q: 140 N 80 30 26 mm 39 mm 1. Find the magnitude of force "F" and, 2. the magnitude of the pin-joint…

A:

Q: The figure shows the chain drive of a bicycle. How far will the bicycle move if the pedals are…

A:

Free undamped vibrations

Whenever an object/system displaces in either side of its equilibrium position with the help of an external/internal means, then the object/system moves regularly or randomly on both sides of its equilibrium position. This motion is called vibration. Generally, there are three types of vibration: longitudinal vibration, transverse vibration, and torsional vibration.